Publicidad
Idiomas disponibles
Idiomas disponibles
Die Gasart am Bedienknebel einstellen.
7.
→ Abb.
37
Wenn sich der Bedienknebel auf der aktuell einge-
stellten Gasart befindet, leuchtet der Leuchtring
des Bedienknebels grün.
Bedienknebelposition
2
3
4
6
Den Bedienknebel mindestens 5 Sekunden auf
8.
der gewünschten Einstellung lassen.
Der Leuchtring des Bedienknebels leuchtet grün.
a
Um die Einstellung zu speichern, bei gedrücktem
9.
Bedienknebel die folgenden Schritte ohne Unter-
brechung ausführen:
Den Bedienknebel auf 0 drehen
‒
Den Bedienknebel eine Rastung nach links auf
‒
12 drehen
.
Den Bedienknebel drei Rastungen nach rechts
‒
auf 1 drehen
.
Den Bedienknebel zwei Rastungen nach links
‒
auf 0 drehen
.
→ Abb.
38
Der Leuchtring geht aus.
a
Die Einstellung ist gespeichert.
a
a
Der Leuchtring des Bedienknebels leuchtet für ei-
nige Sekunden gelb.
Warten, bis der Leuchtring ausgeht.
10.
Funktion nach dem Umbau prüfen
Nach dem Umstellen der Gasart das Gerät auf
1.
Dichtheit prüfen.
Sicherstellen, dass an den Flammen keine gelben
2.
Spitzen sichtbar sind.
Sicherstellen, dass beim schnellen Drehen des
3.
Bedienknebels zwischen der höchsten und der
niedrigsten Stufe der Brenner nicht ausgeht und
kein Flammenrückschlag auftritt.
Umgestellte Gasart dokumentieren
Den Aufkleber mit der umgestellten Gasart in der
▶
Nähe des Typenschilds am Gerät anbringen.
Übersicht der Gasbrenner
→ Abb.
39
en
Scope of delivery
After unpacking all parts, check for any damage in
transit and completeness of the delivery.
→ Fig.
, → Fig.
1
2
Safety clearances
Comply with the safety clearances for the appliance.
→ Fig.
3
*The clearance of 700 mm applies for installation un-
der an extractor hood. For installation under an up-
per cabinet made from combustible material, the
minimum clearance is 760 mm.
Appliance dimensions
You will find the dimensions of the appliance here
→ Fig.
4
Gasart
G20-20 mbar /
G25-25 mbar
G30-29 mbar /
G31-37 mbar
G30-50 mbar
G25-20 mbar
.
Installation accessories
Here, you can find an overview of the installation ac-
cessories.
Use the accessories only as specified. The manufac-
turer shall accept no liability if you use the accessor-
ies incorrectly.
Accessories
Connection strip for flush
installation
Connection strip for sur-
face-mounted installation
General information
Read this instruction manual carefully.
¡
Keep the instruction manual and the
¡
product information safe for future refer-
ence or for the next owner.
Only a licensed expert may connect the
¡
appliance.
Switch off the power supply before carry-
¡
ing out any work.
Never use this appliance in boats or in
¡
vehicles.
Follow the worktop manufacturer's recom-
¡
mendations.
Safe installation
Follow these safety instructions when installing the
appliance.
The appliance can only be used safely if it is cor-
rectly installed according to the safety instructions.
The installer is responsible for ensuring that the ap-
pliance works perfectly at its installation location.
WARNING ‒ Risk of injury!
Parts that are accessible during installation may
have sharp edges and may lead to cutting injuries.
Wear protective gloves.
▶
WARNING ‒ Risk of explosion!
Escaping gas may cause an explosion.
Only a licensed expert may connect the appliance.
▶
Before any work is carried out on the appliance,
▶
switch off the power supply and the gas supply.
For the installation, observe the currently applic-
▶
able building regulations and the regulations of
the local electricity and gas suppliers.
Always check for leaks after working on the gas
▶
connection. The manufacturer assumes no re-
sponsibility for the gas leak at a gas connection
that has previously been handled.
Escaping gas may cause an explosion.
All Installation, connection, regulating and conver-
▶
sion work to a different gas type must be carried
out by an authorised professional while taking into
account the respective applicable regulations and
legal requirements as well as the regulations re-
garding the local electricity and gas suppliers.
Special attention must be paid to the provisions
and guidelines that are applicable for the ventila-
tion. For conversion work to a different gas type,
we recommend that you call the after-sales ser-
vice.
Escaping gas may cause an explosion or poisoning.
Ensure that the room in which installation is to
▶
take place is sufficiently ventilated.
Ensure that there is a door leading outdoors or a
▶
window that can be opened.
For up to 11 kW total power: Ensure that the min-
▶
imum volume of the installation area is 20 m³.
Order number
VA420004
VA420010
13
Publicidad
