Publicidad
Idiomas disponibles
Idiomas disponibles
extension wands. Twist slightly to tighten the connection
(Figure C).
9. Plug the cord into the wall outlet. Your cleaner is ready
for use.
I = ON, O =OFF
NOTE: MANY MORE USEFUL TOOLS ARE AVAILABLE AT YOUR
®
LOCAL DEALER OR SHOP-VAC
WEBSITE.
CASTER SYSTEM ASSEMBLY
Not all units are equipped with the same caster system. Follow the
instructions, which apply to your specific unit.
Without Caster Feet
You will find four casters (Figure 1) with your wet/dry vacuum. Assemble as follows:
1. With cord disconnected from receptacle and tank cover removed, turn tank upside down
so that bottom is facing up.
2. Insert casters into bottom of tank by placing stem of caster into holes provided. Apply
pressure and twisting motion until casters snap into place (Figure 2).
3. Return tank to upright position.
1
With Caster Feet
If your caster feet look like the ones pictured in Figure 3, follow these instructions.
You will find four caster feet (Figure 3), four casters (Figure 4), and four screws with your
wet/dry vacuum. Assemble as follows:
1. With cord disconnected from receptacle and tank cover removed, turn tank upside down
so that bottom is facing up.
2. Remove any webbing that attaches the caster feet to each other.
3. With front of tank inlet facing you, take caster feet marked with the letter A (Figure 5) and
insert stem of caster foot into holes on left front and right rear of tank also marked with
letter A (Figure 6). Make sure caster feet are fully inserted into tank bottom and secure
with screws provided (Figure 7).
4. Take caster feet marked with the letter B (Figure 8) and insert stem of caster foot into
holes on right front and left rear of tank also marked with the letter B (Figure 9). Make
sure caster feet are fully inserted into tank bottom and secure with screws provided
(Figure 10).
5. Insert casters into feet by placing stem of caster into holes provided. Apply pressure and
twisting motion until casters snap into place (Figure 11).
6. Return tank to upright position.
3
4
6
7
A
A
9
10
B
A
B
B
A
B
If your caster feet look like the ones pictured in Figure 12, follow these instructions.
You will find four caster feet (Figure 12), four casters (Figure 13) and four screws with your
C
2
5
8
B
B
11
wet/dry vacuum. Assemble as follows:
1. With cord disconnected from receptacle and tank cover removed, turn tank upside down so
that bottom is facing up.
2. With front of tank facing you, take caster feet marked with the letter A (Figure 14) and
place in slots on left front and right rear of tank also marked with the letter A (Figure 15).
Secure with screws provided (Figure 16).
3. Take caster feet marked with the letter B (Figure 17) and place in slots on right front and
left rear of tank also marked with the letter B (Figure 18). Secure with screws provided
(Figure 19).
4. If flat washers are included in hardware package place flat washer over stem of caster
before installing casters into feet. NOTE: Flat washers are not required with all units.
5. Insert casters into feet by placing stem of caster into holes provided. Apply pressure and
twisting motion until casters snap into place (Figure 20). Return tank to upright position.
12
15
A
A
A
A
18
B
A
B
B
A
B
With Rear Caster Dolly/Tool Holder
You will find four casters (Figure 21), two caster feet (Figure 22), rear caster dolly/tool holder
(Figure 23), and four screws with your wet/dry vacuum. Assemble as follows:
21
1. With cord disconnected from receptacle and tank cover removed, turn tank upside down so
that the bottom is facing up.
2. Take rear caster dolly and place into slots (on rear of tank, opposite of drain) and secure
with screws provided (Figure 24).
3. If flat washers are included in hardware package place flat washer over stem of caster
before installing casters into feet. NOTE : Flat washers are not required with all units.
4. Insert casters into bottom of rear caster dolly by placing stem of caster into holes provided.
Apply pressure and twisting motion until casters snap into place (Figure 25).
5. With tank drain facing you, take caster foot marked with the letter A (Figure 26) and place
in slot on left side of tank also marked with the letter A. Secure with screw provided
(Figure 27).
6. Take caster foot marked with the letter B (Figure 28) and place in slot on right side of tank
also marked with the letter B. Secure with screw provided (Figure 29).
7. Insert casters into feet by placing stem of casters into holes provided. Apply pressure and
B
twisting motion until casters snap into place (Figure 30).
8. Return tank to upright position.
9. Place tool basket (not standard with all models) with curved surface against tank on rear
caster dolly assembly (Figure 31).
24
13
14
16
17
B
19
20
22
23
25
26
A
A
B
B
A
Publicidad
