Publicidad
Idiomas disponibles
Idiomas disponibles
USER & SET=UP iNSTRUCTiONS
PERM,
DELICATES
QUICK
PRESS
AND KNITS
CYCLE
1. Door must be closed before cycle selection is made.
2. Press fabric setting button for the wash cycle desired. After
the cycle is started, the time will display and count down.
General
User information
Scrolling
'out of order' showing
in display, followed
by a failure code
This condition indicates the washer is inoperative.
'0 Minutes' showing
in display
This condition indicates the washer cannot be operated. Coins
dropped or debit inputs during this condition will be stored in
escrow but cannot be used until normal operation is restored by
opening and closing the door. If a door switch fails, it must be
replaced before normal operation can be restored.
Cold Start (Initial first use)
Washer is programmed
at the factory as follows:
Display
After the washer has been installed and plugged in, the display
will show "0 MINUTES." Once the washer has been plugged in
and the washer door opened and closed, the display will show
the price. In washers set for free cycles, the display will flash
"SELECT CYCLE."
WHI
I'E8
COLORS
BRIGRTS
PERM.
DELICATES
QUICK
PRESS
AND KNITS
CYCLE
NOTE: Not displayed on washer as shown. Message scrolls
followed by the failure code.
WHITES
COLORS
BRJGHT5
pERM.
DELICATES
QUICK
PRESS
AND KNITS
CYCLE
11-minute wash period
3 rinses (extra rinse not enabled)
7 x coin 1 wash price (PD models)
_q
_q
!
WHI)3ES
COLORS
BR_GIIT8
PER_.
DELICATES QUICK
PRESS
AND KNITS
CYCLE
Warm Start (after power failure)
A few seconds after power is restored, if a cycle was in progress
at the time of the power failure, 'RESELECT CYCLE' will flash
in the display, indicating the need for a button press to restart
washer.
rmq _q
rJ
WHITES
COLORS
BRIGHTS
PERM.
DELICATE$
QUICK
pRESS
AND KNr¢8
CYCLE
Door Lock
The door will be locked when the cycle starts. The door
will remain locked until the end of a cycle or approximately
2 minutes after a power interruption.
Pricing
After the door is opened following the completion of a cycle, the
display indicates the cycle price (unless set for free operation).
As coins are dropped or debit inputs arrive, the display will
change to lead the user through the initiation of a cycle.
Free Cycles
This is established
by setting the cycle price to zero. When this
happens, 'SELECT CYCLE' will appear rather than a cycle price.
Control
Set-up
Procedures
IMPORTANT:
Read all instructions
before operating.
[]
PD Models: insert access door key, turn, and lift to remove
access door.
Set-up procedures can be entered by using the Service Access
Code (see Service Access Code section) for PN washers set up
without a key switch installed.
The washer is now in the set-up mode. The lower fabric setting
buttons and the digital display are used to set up the controls.
The display can contain 4 numbers and/or letters and a decimal
point. These are used to indicate the set-up codes and related
code values available for use in programming
the washer.
Once the washer has been programmed
with a hand held device
using Accu Trac, or a Gen. 2 card reader has been installed, the
washer will be put into dAS mode permanently, and dAS will be
displayed every time set-up mode is accessed.
How to use the buttons
to program
controls
1. The PERM. PRESS button is used to adjust the values
associated with set-up codes. Pressing this button will
change the value by increments.
Rapid adjustment is
possible by holding the button down.
2. The DELICATES AND KNITS button advances you through
the set-up codes. Pressing this button will advance you to the
next available set-up code. Holding the button down will
automatically
advance through the set-up codes at a rate of
1 per second.
11
Publicidad
