Explanation Of General View - Makita LH1040 Manual De Instrucciones

ENGLISH
(Original instructions)
1 Auxiliary plate
2 Hex bolt(s)
3 Base
4 Nut
5 Holders
6 Holder
7 Adjuster
8 Screw
9 Bolt
10 Lower blade guard A
11 Lower blade guard B
12 Top blade guard
13 Handle
14 Lever
15 Socket wrench
16 Adjusting bolt
17 Top surface of turn base
18 Periphery of blade
19 Guide fence
20 Pointer
21 Lock lever
22 Grip
23 Miter scale
24 Bevel scale
25 Switch
26 Lamp switch
27 Lamps
28 Stopper pin
29 Clamping screw
30 Top table
31 Motor housing
SPECIFICATIONS
Model
Blade diameter .................................................................................................................................. 255 mm – 260 mm
Blade body thickness............................................................................................................................ 1.6 mm – 1.8 mm
Riving knife thickness ........................................................................................................................................... 2.0 mm
Hole diameter
For all countries other than European countries ........................................................................... 25.4 mm and 25 mm
For European countries ......................................................................................................................................30 mm
Max. Cutting capacities (H x W) with blade 260 mm in diameter in the miter saw mode
Bevel angle
0°
45° (left)
Max. Cutting capacities at 90° in the table saw (bench saw mode)....................................................................... 40 mm
–1
No load speed (min ) ............................................................................................................................................ 4,800
Table size (W x L) ............................................................................................................................... 260 mm x 405 mm
Dimensions (L x W x H) .....................................................................................................530 mm x 476 mm x 535 mm
Net weight ............................................................................................................................................................ 14.3 kg
Safety class ................................................................................................................................................................ /II
• Due to our continuing program of research and development, the specifications herein are subject to change without
notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003

Explanation of general view

32 Center cover
33 Blade guard A
34 Shaft lock
35 Saw blade
36 Blade guard B
37 Blade case
38 Arrow
39 Outer flange
40 Inner flange
41 Spindle
42 Ring
43 Riving knife
44 Area to press in
45 Blade width
46 Rip fence holder
47 Guide rail on the top table
48 Clamping screw (A)
49 Clamping screw (B)
50 Rip fence
51 Workpiece
52 Line to be aligned with
53 Square nut
54 Washer
55 Scale
56 Two screws
57 Dust nozzle
58 Dust bag
59 Fastener
60 Cap
61 Vacuum cleaner
62 Blade cover
0°
69 mm x 130 mm
93 mm x 95 mm
35 mm x 130 mm
53 mm x 95 mm
63 Support
64 Turn base
65 Sub-fence
66 Vise rod
67 Vise knob
68 Vise arm
69 Holder assembly
70 Projection
71 Vise shaft
72 Rod 12
73 Vise (optional accessory)
74 Vise
75 Spacer block
76 Aluminum extrusion
77 Set plate
78 Small boss
79 Face/edge parallel
80 Wood screw
81 Glue together
82 Hole (7 mm in diameter)
83 Bolt M6
84 Push stick
85 Auxiliary fence
86 Push block
87 Triangular rule
88 0° adjusting bolt
89 Arm
90 45° bevel angle adjusting bolt
91 Limit mark
92 Screwdriver
93 Brush holder cap
Miter angle
right 69 mm x 85 mm, 93 mm x 67 mm
left 69 mm x 85 mm, 93 mm x 67 mm
right 35 mm x 91 mm, 49 mm x 67 mm
left 35 mm x 65 mm, 49 mm x 42 mm
LH1040/LH1040F
45°
13