General Power Tool Safety Warnings; Screwdriver Safety Warnings; Functional Description - Makita 6822 Manual De Instrucciones

ENGLISH
(Original instructions)
1 Locking sleeve
2 Approximately 1 mm
3 Locator
4 Low
SPECIFICATIONS
Model
Capacities
Self drilling screw ................................................. 6 mm
Drywall screw ...................................................... 5 mm
Bit shank size .....................................................1/4" Hex
–1
No load speed (min ) ...................................... 0 – 4,000
Overall length .................................................... 258 mm
Net weight .............................................................. 1.3 kg
Safety class ...............................................................
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2014
Intended use
The tool is intended for screw driving in wood, metal and
plastic.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.

General Power Tool Safety Warnings

WARNING Read all safety warnings, instructions,
illustrations and specifications provided with this
power tool. Failure to follow all instructions listed below
may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future
reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.

SCREWDRIVER SAFETY WARNINGS

1. Hold the power tool by insulated gripping sur-
faces, when performing an operation where the
fastener may contact hidden wiring or its own
cord. Fasteners contacting a "live" wire may make
exposed metal parts of the power tool "live" and
could give the operator an electric shock.
2. Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
3. Hold the tool firmly.
4. Keep hands away from rotating parts.
Explanation of general view
5 High
6 Speed control screw
7 Switch trigger
8 Lock button
5.
6822
6.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
/II
to safety rules for the subject product. MISUSE or
failure to follow the safety rules stated in this instruc-
tion manual may cause serious personal injury.

FUNCTIONAL DESCRIPTION

CAUTION:
ENE033-1
• Always be sure that the tool is switched off and
unplugged before adjusting or checking function on the
tool.
Depth adjustment
The depth can be adjusted by turning the locking sleeve.
ENF002-2
Turn it in "A" direction for less depth and in "B" direction
for more depth. One full turn of the locking sleeve equals
1.5 mm change in depth. (Fig. 1)
Adjust the locking sleeve so that the distance between
the tip of the locator and the screw head is approximately
1 mm as shown in Fig. 2 or 3. Drive a trial screw into your
material or a piece of duplicate material. If the depth is
GEA010-2
still not suitable for the screw, continue adjusting until you
obtain the proper depth setting. (Fig. 2 & 3)
Switch action (Fig. 4)
CAUTION:
• Before plugging in the tool, always check to see that
the switch trigger actuates properly and returns to the
"OFF" position when released.
To start the tool, simply pull the switch trigger. Tool speed
is increased by increasing pressure on the switch trigger.
Release the switch trigger to stop.
For continuous operation, pull the switch trigger and then
push in the lock button.
GEB135-1
To stop the tool from the locked position, pull the switch
trigger fully, then release it.
A speed control screw is provided so that maximum tool
speed can be limited (variable). Turn the speed control
screw clockwise for higher speed, and counterclockwise
for lower speed.
NOTE:
• Even with the switch on and motor running, the bit will
not rotate until you fit the point of the bit in the screw
head and apply forward pressure to engage the clutch.
9 Reversing switch lever
10 Bit
11 Magnetic bit holder
Do not touch the bit or the workpiece immedi-
ately after operation; they may be extremely hot
and could burn your skin.
Always secure workpiece in a vise or similar
hold-down device.
3