Technical Data; Ec Declaration Of Conformity; Paper Shredder Hsm Classic 125.2 - HSM Classic 125.2 Instrucciones De Servicio

https://www.supplychimp.com

10 Technical data

Cutting type
Shred size (mm)
Sa fe ty ra ting German DIN 32757 – 1
Cutting ca pa ci ty** (Sheet), DIN A4 70 g/m
Cutting speed
Weight
Noise level (Idle running/ load)
Lo ading width
Voltage
Power for the maximum number of sheets
Operating mode
Ambient conditions in operation:
Temperature
Relative humidity
Height above sea-level (MSL)
Dimensions W x D x H (mm)
Volume of shredded material bag
* HSM-specifi cation
** The maximum number of sheets (DIN A4, 70 g/m² or 80 g/m²), fed lengthways, which can be cut in one cycle. The
performance data is determined when the motor is cold and the cutting device is freshly oiled. A weaker mains voltage
or a different mains frequency to the one specifi ed could result in less sheet capacity and increased noise during op-
eration. The sheet capacity can vary depending on the structure and properties of the paper and on the way it enters.
The performance data in 80 g/m² is calculated.

EC Declaration of Conformity

The manufacturer HSM GmbH + Co. KG, Austraße 1 - 9, D-88699 Frickingen hereby declares that the machine,
referred to here as
document shredder HSM Classic 125.2
corresponds to the health and safety requirements of the following EC directives listed below due to its conception and
design of the version in which it was put into circulation by us:
Low voltage directive 2006 / 95 / EEC
EMC directive 2004 / 108 / EC
Applied standards and technical specifi cations:
• EN 55014-1:2006
• EN 55014-2:1997 + A1:2001 + A2:2008
• EN 61000-3-2:2006
• EN 61000-3-3:1995 + A1:2001 + A2:2005
• EN 13849-1:2008
• EN 62233:2008
Frickingen, 01.03.2010
The machine type was tested for compliance with the requirements of the EC directives by:
TÜV Rheinland Product Safety GmbH, Am Grauen Stein, 51105 Köln/Germany
This test centre is responsible according to the EC directives.
14
2 28 - 30
80 g/m 2 22 - 24
• EN 61000-4-2:1995 + A1:1998 + A2:2001
• EN 61000-4-4:2004
• EN 61000-4-5:2006
• EN 61000-4-6:2007
• EN 61000-4-11:2004
Rolf Gasteier - Technical Director
Strip cut
5.8 3.9 1.9 3.9 x 30
2 2 3
22 - 24 16 - 18
17 - 19 13 - 14
120 mm/s
26 kg
60 dB(A) / 64 dB(A)
100 V, 50/60 Hz – 115 V, 60 Hz
Continuous operation
-10 °C to +40 °C
max. 90 %, without condensation
448 x 347 x 828
Classic 125.2
english
Cross cut
1.9 x 15 0.78 x 11
3 4 5
15 - 18 10 - 12 6 - 8
12 - 14 8 - 10 5 - 7
130 mm/s
30 kg
62 dB(A) / 64 - 70 dB(A)
255 mm
230 V, 50 Hz
670 W
max. 2,000 m
76 l
1 x 5
Level 6*
4 - 5
3 - 4
09/2011