Additional Safety Rules; Functional Description - Makita 2012NB Manual De Instrucciones

ADDITIONAL SAFETY RULES

1. Wear eye protection.
2. Wear suitable personal protective equipment
when necessary, such as hearing protection (ear
plugs), respiratory protection (dust mask) and
gloves when handling rough material.
3. Do not use the tool in the presence of flammable
liquids or gases.
4. Make sure that all covers are installed in place
before operation.
5. Handle the blades very carefully.
6. Check the blades carefully for cracks or damage
before operation. Replace cracked or damaged
blades immediately.
7. Tighten the planer blade installation bolts
securely.
8. Remove nails and clean the workpiece before
cutting. Nail, sand or foreign matter can cause
blade damage.
9. Do not remove chips from the chip chute when
the motor is running. Clean out chips after the
blades come to a complete stop. Always use a
stick etc. when cleaning them out.
10. Do not leave the tool running.
11. Do not abuse cord. Never yank cord to discon-
nect it from receptacle. Keep cord away from
heat, oil water and sharp edges.
SAVE THESE INSTRUCTIONS.
INSTALLATION
Movement and transport of thicknesser (Fig. 1)
CAUTION:
• Watch your step when moving the tool.
Fold the sub-tables. Grasp the carrying handles when
moving the tool.
When transporting it by vehicle, secure with a rope or
other substantial means to prevent tipping or movement.
Positioning the thicknesser (Fig. 2)
Locate the tool in a well lit and level place where you can
maintain good footing and balance. Bolt/screw it to the
workbench or thicknesser stand (optional accessory)
using the bolt holes provided in the base.

FUNCTIONAL DESCRIPTION

CAUTION:
• Always be sure that the tool is switched off and
unplugged before adjusting or checking function on the
tool.
Switch action (Fig. 3)
CAUTION:
• Before plugging in the tool, always be sure that the tool
is switched off. The pilot lamp lights up when the tool is
plugged into the power source.
To start the tool, press the ON (I) button. To stop it, press
the OFF (O) button.
8
Dimensional adjustment (Fig. 4)
Lower the main frame by turning the crank handle coun-
ENB065-1
terclockwise until the indicator plate points to the scale
graduation indicating the desired finished dimension.
One full turn of the crank handle moves the main frame
2 mm up or down. The scale has inch graduations on its
right side and metric graduations on its left side.
Adjusting depth of cut
The maximum depth of cut differs depending upon the
width of workpiece being cut. Refer to the table. When
you need to remove more than the amount specified in
the table, set the depth of cut shallower than the amount
and make two or more passes.
Width of workpiece
being cut
Less than 150 mm
150 mm – 240 mm
240 mm – 304 mm
To adjust the depth of cut, proceed as follows.
Insert the workpiece flat on the table top. Lower the main
frame by turning the crank handle counterclockwise. The
depth gauge will rise and the amount of gauge rise indi-
cates the depth of cut. (Fig. 5)
CAUTION:
• Always lower the main frame when aligning the indica-
tor plate with the graduation indicating the desired fin-
ished dimension. If you raise the main frame into the
desired finished dimension, additional play in the screw
may result. This may cause an undesired finished
dimension.
• Always place the workpiece flat on the table top when
predetermining the depth of cut. Otherwise, the prede-
termined depth of cut will differ from actual depth of cut.
Depth adjusting gauge (Fig. 6)
Use the depth adjusting gauge when you need to prede-
termine the depth of cut more accurately. To do so, pro-
ceed as follows.
First, plane the workpiece at the predetermined depth of
cut. Measure the thickness of the planed piece to know
how much more stock you need to remove.
Turn the depth adjusting gauge on the crank handle until
the 0 graduation is aligned with the groove on the tool.
Now turn the crank handle counterclockwise until the
graduation for the desired depth of cut is aligned with the
groove on the tool.
When you need to remove more than the amount speci-
fied in the table mentioned in the "Adjusting depth of cut"
section, set the depth of cut shallower than the amount
and make two or more passes.
Stopper (Fig. 7)
Use the stopper when you need to plane many work-
pieces to the same thickness. To do so, proceed as fol-
lows.
Turn the crank handle until the indicator plate points to
the scale graduation indicating the desired finished
dimension.
Depress the stopper button and lower the stopper until it
just contacts the table top.
If you need fine adjustment of the stopper, turn the stop-
per knob.
Maximum depth of cut
3.0 mm
1.5 mm
1.0 mm