Steam Ironing - Sunbeam 3016 Manual De Instrucciones

T F W R
O Ill ThE ATER
1. M ake sure the iron is unplugged. Set the Steam Lever to (Dry) and the Fabric Select to OFF.
2. Lift the Water Fill Hole Cover.
3. F ill water cup with tap water. Pour water into iron water reservoir. Do not fill water reservoir beyond maximum
fill level.
WARNING: To prevent the risk of burns, be careful when filling a hot iron with water. Hot metal parts, hot water
and steam can cause injuries.
D I
Ry RONING
1. Make sure the Steam Lever is turned to the (Dry) setting.
2. Plug the cord into a 120-Volt AC outlet.
3. S elect the fabric setting you desire (Silk or Synthetics). Allow the iron to heat for 2 minutes.
While the iron is heating, make sure it is sitting on its heel rest on a stable, protected surface.
Note: While the Steam Lever is turned to the (Dry) setting, you may still use the SHOT OF STEAM
MIST feature. Please make sure the water reservoir is approximately ¼ full of water.
®
S I
TEAM RONING
1. Follow the instructions for "Filling the Water Reservoir."
2. Plug the cord into a 120-Volt AC outlet.
3. S elect the fabric setting you desire (Synthetic, Silk, Linen, Cotton or Wool). Allow the iron to heat for 2 minutes.
While the iron is heating, make sure it is sitting on its heel rest on a stable, protected surface.
4. A llow the iron to heat for 2 minutes, and then turn the Steam Lever to the appropriate setting.
IMPORTANT: When not ironing, always set the Steam Lever to (Dry) and the Fabric Select to OFF.
S M F is a powerful water spray mist that dampens the fabric to aid in removing wrinkles from
®
PRAy IST EATURE
heavy fabrics and for setting creases.
To use the Spray Mist
®
S S F
®
hOT OF TEAM EATURE
You can use this feature while Dry or Steam ironing. The water reservoir must be approximately ¼ full of water.
To use the Shot of Steam
each time you would like an extra burst of steam. The SHOT OF STEAM
just a short pause between shots.
WARNING: To prevent the risk of burns, keep your hand away from the area being steamed.
WARNING: DO NOT steam garments while wearing them; this may result in injuries.
M S A
®
OTION MART UTO
When the iron is plugged in, the Power Indicator will light steadily, indicating that there is power to the iron.
If you leave the iron:
1. i n a horizontal position without moving it, or accidentally tip the iron over, it will automatically stop heating
after 30 seconds. The Power Indicator will blink to let you know that the iron has stopped heating.
2. i n a vertical position (on its heel rest) without moving it, the iron will automatically turn off after 15 minutes.
The Power Indicator will blink to let you know that the iron has stopped heating.
IMPORTANT: The Power Indicator will continue to blink until the iron is unplugged or reset.
To reset the iron:
Move the iron back and forth and allow it to reheat for 2 minutes. The indicator will stop blinking and the iron
will start heating again.
WARNING: The patented MOTION SMART
your iron off. See "Caring for Your Iron After Use" for information on turning off your iron and storing it safely
between use.
S S I
®
TORAGE TRIP NDIcATOR
To use the Storage Strip
(use tap water)
ESERvOIR
U
SING ThE
Feature: Press the SPRAY MIST
(select models only) provides an extra burst of steam for deep penetration of stubborn wrinkles.
Feature: Place the iron on top of the wrinkle and press the SHOT OF STEAM
®
-O F
FF EATURE
Auto-Off is a safety feature, not a recommended means for turning
®
is an easy way to see when the iron is cool enough to store.
Indicator: Turn iron on. In approximately 2 minutes, the STORAGE STRIP
®
I ' S F
RON S PEcIAl EATURES
button firmly.
®
English - 3
feature may be used continuously with
®
or SPRAY
®
button
®
Indicator
®