Power Supply Of The On-Board Computer; Storage Mode/Resetting The Kiox; Displays And Settings Of The On- Board Computer; Operating Logic - Bosch Kiox BUI330 Instrucciones De Servicio

ically reactivated as soon you start pedalling again and the
speed is below 25/45 km/h.
The following options are available for switching off the
eBike system:
– Press the On/Off button (4) on the on-board computer
for at least 1 second.
– Switch off the eBike battery using its On/Off button (bi-
cycle manufacturer-specific solutions are possible
whereby there is no access to the battery On/Off button;
see the bicycle manufacturer operating instructions).
– Remove the on-board computer from its holder.
If no power is drawn from the eBike drive for about
10 minutes (e.g. because the eBike is not moving) and no
button is pressed on the on-board computer or the operating
unit of the eBike, the eBike system, and therefore also the
battery, will switch off automatically to save energy.

Power supply of the on-board computer

If the on-board computer is in the holder (5), a sufficiently
charged eBike battery is inserted into the eBike and the
eBike system is switched on, then the on-board computer
battery is powered by the eBike battery.
If the on-board computer is removed from the holder (5),
the power is supplied by the on-board computer battery. If
the on-board computer battery's charge is running low, a
warning message appears on the display.
To charge the on-board computer battery, slide the on-board
computer back onto the holder (5). Note that if you do not
charge the eBike battery straight away, the eBike system will
automatically switch off after 10 minutes of inactivity. If this
happens, the on-board computer battery will also stop char-
ging.
You can also charge the on-board computer via the USB
port. To do this, open the protective cover (17). Use a Mi-
cro-USB cable to connect the USB port (6) on the on-board
computer to a standard USB charger (not included with the
product as standard) or to the USB port of a computer (5 V
charging voltage; max. 500 mA charging current).
If the on-board computer is removed from the holder (5), all
values for the functions are saved and can still be displayed.
If the Kiox battery is not recharged, the date and time will be
retained for up to six months. When the on-board computer
is switched on again, the date and time will be reset if a
Bluetooth connection to the app has been established and
the smartphone has successfully identified the current loca-
tion via GPS.
Note: The Kiox only charges while it is switched on.
Note: If the Kiox is switched off during charging via a USB
cable, the Kiox can only be switched on again once the USB
cable has been disconnected.
Note: To maximise the lifespan of the on-board computer's
battery, it should be recharged for one hour every three
months.
Bosch eBike Systems

Storage mode/resetting the Kiox

The on-board computer has an energy-saving storage mode
which minimises the rate at which the internal battery dis-
charges. Setting to this mode erases the date and time.
This mode can only be activated pressing and holding the
on/off button (4) of the on-board computer at least 8
seconds.
If the on-board computer does not start when the on/off but-
ton (4) is pressed briefly, the on-board computer is in stor-
age mode.
You can deactivate storage mode by pressing the on/off but-
ton (4) for at least 2 seconds.
The on-board computer detects whether it is in a stable con-
dition. If you press and hold the on/off button (4) for at least
8 seconds while in a stable condition, the on-board com-
puter will go into storage mode. If, contrary to expectations,
the Kiox is not in a stable condition and cannot be operated,
pressing and holding the on/off button (for at least 8
seconds) will reset it. After being reset, the on-board com-
puter will restart automatically after approx. 5 seconds. If
the Kiox does not restart, press the on/off button (4) for
2 seconds.
To reset the Kiox to its factory settings, select <Settings> →
<Sys settings> → <Reset [name of BUI]>. All user data will
be lost.
Displays and settings of the on-
board computer
Please note: All screenshots showing the display and text
on the following pages are from the approved software ver-
sion. Due to the fact that the software is updated several
times a year, the display and/or text may change slightly fol-
lowing an update.

Operating logic

You can use the < (10) and > (8) buttons to switch between
the different riding value information pages (even while rid-
ing). This way, you can keep both hands on the handlebars
while cycling.
You can use the + (12) and – (11) buttons to increase or de-
crease the assistance level. If you are in a list (e.g. the <Set-
tings> menu), you can use these buttons to scroll up or
down in the list.
The <Settings> that can be accessed via the status page
cannot be changed while riding.
You can use the select button (9) to perform the following
functions:
– You can access the quick menu while riding.
– You can access the settings menu from the status page
while stationary.
– You can confirm values and acknowledge informative
hints.
– You can exit a dialogue.
English – ​ 3
1 270 020 XBK | (17.05.2018)