Removing/Inserting The Battery - Milwaukee 2701-20 Manual Del Operador

ASSEMBLY
Recharge only with the charger
WARNING
specified for the battery. For spe-
cific charging instructions, read the operator's
manual supplied with your charger and battery.

Removing/Inserting the Battery

To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
Always remove battery pack before
WARNING
changing or removing accessories.
To insert the battery, slide the pack into the body
of the tool. Make sure it latches securely into place.
Only use accessories specifically
WARNING
recommended for this tool. Others
may be hazardous.
To reduce the risk of injury, always use a side
handle when using a 9.0 Ah or higher capac-
ity battery pack with this tool. Always brace or
hold securely. Ensure side handle is tightened
securely before each use.
Installing the Side Handle
If your drill/driver did not come with a side handle,
visit www.milwaukeetool.com for the appropriate
accessory handle.
1. To install the side handle, loosen
the side handle grip until the
hooks are far enough apart to fit
into the slots on the gear case
ring. Position the side handle on
the top, pointing to the left or
right. Tighten the side handle grip
until it is secure.
2. To remove the side handle,
loosen the side handle grip until
the side handle can be removed. Reposition and
tighten securely.
OPERATION
Always remove battery pack before
WARNING
changing or removing accesso-
ries. Only use accessories specifically recom-
mended for this tool. Others may be hazardous.
To reduce the risk of injury, always wear safety
goggles or glasses with side shields.
Installing Bits
Always remove the battery before inserting or remov-
ing bits. Select the proper style and size bit for the job.
This tool is equipped with a spindle lock. The chuck
can be tightened with one hand, creating higher grip
strengths on the bit.
1. To open the chuck jaws, turn the sleeve in the
counterclockwise direction.
When using drill bits, allow the bit to strike the
bottom of the chuck. Center the bit in the chuck
jaws and lift it about 1/16" off of the bottom.
When using screwdriver bits, insert the bit far
enough for the chuck jaws to grip the hex of the bit.
2. To close the chuck jaws, turn the sleeve in the
clockwise direction. The bit is secure when the
chuck makes a ratcheting sound and the sleeve
can not be rotated any further.
3. To remove the bit, turn the sleeve in the counter-
clockwise direction.
NOTE: A ratcheting sound may be heard when the
chuck is opened or closed. This noise is part of the
locking feature, and does not indicate a problem with
the chuck's operation.
1. To use the drilling mode, rotate
the torque selector collar until the
drill symbol
with the arrow.
2. To use the driving mode rotate
the torque selector collar until
the desired clutch setting ap-
pears in line with the arrow.
The adjustable clutch, when
properly adjusted, will slip at a
preset torque to prevent driving
the screw too deep into different
materials and to prevent damage
to the screw or tool.
Selecting Hammer, Drill or Drive Action
1. To use the hammer-drilling
mode, rotate the application
selector collar until the hammer
symbol
the arrow. Apply pressure to the
bit to engage the hammering
mechanism.
Hooks
NOTE: The number selected on
the torque selector collar has no
effect on operation of the drill in hammer mode.
NOTE: When using carbide bits, do not use water
Slots
to settle dust. Do not attempt to drill through steel
reinforcing rods. This will damage the carbide bits.
2. To use the drilling only mode,
rotate the application selector
collar until the drill symbol
appears in line with the arrow.
NOTE: The number selected on
the torque selector collar has no
effect on operation of the drill in
drilling mode.
3. To use the driving screws
mode rotate the application se-
lector collar until the drive symbol
row. Then rotate the torque se-
lector collar until the desired
clutch setting appears in line with
the arrow.
The adjustable clutch, when
properly adjusted, will slip at a
preset torque to prevent driving the screw too deep
into different materials and to prevent damage to
the screw or tool.
The torque specifications shown here are approxi-
mate values obtained with a fully charged battery
pack.
Clutch
Setting in. lbs
1-3
4-6
7-9
10-13
14-16
4
Selecting Drill or Drive Action
(Cat. No. 2701-20)
appears in line
(Cat. No. 2702-20)
appears in line with
appears in line with the ar-
Cat. No. 2701-20
Applications
25-28 Small screws in softwood.
29-34
Medium screws in softwood or small
screws in hardwood.
36-39
Large screws in softwoods. Medium
40-44
screws in hardwood or large screws in
46-50
hardwood with pilot hole.