Makita BTD200 Manual De Instrucciones página 3

Ocultar thumbs Ver también para BTD200:
Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 24
ENGLISH
1
Battery cartridge
2
Button
3
Terminal cover
4
Charging lights
5
Battery charger
6
Bit
SPECIFICATIONS
Model
Capacities
Wood screw ......................................................... 6 mm
Self drilling screw ................................................. 6 mm
Hex screw ............................................................ 6 mm
-1
No load speed (min
) ............................. High: 0 – 2,000
Impacts per minute ..................................High: 0 – 3,000
Overall length ..................................................... 232 mm
Net weight .............................................................. 2.9 kg
Rated voltage ...................................................D.C. 24 V
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.
IMPORTANT SAFETY INSTRUCTIONS
FOR CHARGER & BATTERY CARTRIDGE
1.
SAVE THESE INSTRUCTIONS — This manual
contains important safety and operating instruc-
tions for battery charger.
2.
Before using battery charger, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (2) product using bat-
tery.
3.
CAUTION — To reduce risk of injury, charge only
MAKITA type rechargeable batteries. Other types
of batteries may burst causing personal injury
and damage.
4.
Do not expose charger to rain or snow.
5.
Use of an attachment not recommended or sold
by the battery charger manufacturer may result
in a risk of fire, electric shock, or injury to per-
sons.
6.
To reduce risk of damage to electric plug and
cord, pull by plug rather than cord when discon-
necting charger.
7.
Make sure cord is located so that it will not be
stepped on, tripped over, or otherwise subjected
to damage or stress.
8.
Do not operate charger with damaged cord or
plug — replace them immediately.
Explanation of general view
7
Sleeve
8
Switch trigger
9
Reversing switch lever
10 A side
11 B side
12 Clockwise
9.
BTD200
10. Do not disassemble charger or battery cartridge;
11. To reduce risk of electric shock, unplug charger
Low: 0 – 1,600
Low: 0 – 2,500
12. The battery charger is not intended for use by
13. Young children should be supervised to ensure
14. If operating time has become excessively
15. If electrolyte gets into your eyes, rinse them out
ADDITIONAL SAFETY RULES
FOR CHARGER & BATTERY CARTRIDGE
1.
2.
3.
4.
5.
6.
7.
8.
13 Counterclockwise
14 Speed change lever
15 Limit mark
16 Brush holder cap
17 Screwdriver
Do not operate charger if it has received a sharp
blow, been dropped, or otherwise damaged in
any way; take it to a qualified serviceman.
take it to a qualified serviceman when service or
repair is required. Incorrect reassembly may
result in a risk of electric shock or fire.
from outlet before attempting any maintenance
or cleaning. Turning off controls will not reduce
this risk.
young children or infirm persons without super-
vision.
that they do not play with the battery charger.
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
with clear water and seek medical attention right
away. It may result in loss of your eyesight.
Do not charge battery cartridge when tempera-
ture is BELOW 10°C (50°F) or ABOVE 40°C
(104°F).
Do not attempt to use a step-up transformer, an
engine generator or DC power receptacle.
Do not allow anything to cover or clog the
charger vents.
Do not short the battery cartridge:
(1) Do not touch the terminals with any conduc-
tive material.
(2) Avoid storing battery cartridge in a container
with other metal objects such as nails, coins,
etc.
(2) Do not expose battery cartridge to water or
rain.
A battery short can cause a large current flow,
overheating, possible burns and even a break-
down.
Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50°C (122°F).
Do not incinerate the battery cartridge even if it
is severely damaged or is completely worn out.
The battery cartridge can explode in a fire.
Be careful not to drop, shake or strike battery.
Do not charge inside a box or container of any
kind. The battery must be placed in a well venti-
lated area during charging.
3

Publicidad

Tabla de contenido
loading

Tabla de contenido