Using Subaddresses - IMG STAGELINE PARC-56/RGB Manual De Instrucciones

5.3.3 Setting the DMX start address
GB
For separate control of all DMX units connected to
the light controller, each unit must have its own
start address. If the first DMX channel of the spot-
light is to be controlled by the light controller via
DMX address 17, for example, set the start address
on the spotlight to 17. All other DMX channels of the
spotlight will be automatically assigned to the fol-
lowing addresses. The following table is an exam-
ple with the start address 17:
Number of
DMX channels
3
4
5
10
Fig. 2 DMX address assignment for start address 17
1) Press the button MENU repeatedly until the
highest menu level has been reached.
2) Press the button UP or DOWN repeatedly until
the display indicates
3) Press the button ENTER. The display indicates
and a number between 1 and 512.
4) Use the button UP or DOWN to set the start
address.
5) Now the spotlight can be operated with the light
controller.
If not, go to the menu item
button ENTER. If the display indicates
use the button UP or DOWN to set the indication
to .

5.3.4 Using subaddresses

With subaddresses, it is possible to independently
control up to 66 spotlights (spotlight groups) via
one DMX start address. Thus, the maximum num-
ber of DMX units that may be controlled is sub-
stantially increased. The spotlights with a subad-
dress are selected via DMX channel 10 (fig. 8). All
spotlights with the same subaddress may be con-
trolled in sync if DMX channel 10 is set to a DMX
value smaller than 10.
1) Set the spotlight for the control via 10 DMX
channels,
setting
2) Press the button MENU repeatedly until the
highest menu level has been reached.
3) Press the button UP or DOWN repeatedly until
the display indicates
4) Press the button ENTER. The display indicates
and a number between 01 and 66.
16
DMX Next possible start address
addresses for the
assigned succeeding DMX unit
17 – 19
17 – 20
17 – 21
17 – 26
.
and press the
chapter 5.3.2 (menu item
).
.
5) Use the button UP or DOWN to set the sub -
address.
6) Press the button MENU repeatedly until the dis-
play indicates
7) Press the button UP three times so that the dis-
play indicates
8) Press the button ENTER. The display indicates
9) Press the button UP or DOWN repeatedly until
the display indicates
10) Press the button ENTER. If the display indicates
20
vated. If it indicates
21
DOWN to set the indication to
22
11) To be able to control the spotlight by DMX, press
27
the button MENU twice to return to the highest
menu level.
12) To be able to operate the spotlight, set the DMX
channel 10 at the light controller to the DMX
value that corresponds to the sub address of the
spotlight:
DMX
value
000 – 009
010 – 019
020 – 029
030 – 039
040 – 049
,
050 – 059
060 – 069
070 – 079
080 – 089
090 – 099
100 – 109
110 – 119
120 – 129
130 – 139
140 – 149
150 – 159
160 – 169
170 – 179
,
180 – 189
190 – 199
200 – 209
210
211
Fig. 3 Selection of spotlights with a subaddress via DMX
again.
.
, , , ,
.
, the function for subaddress selection is acti-
Sub - DMX
address value address
all
01 212
02 213
03 214
04 215
05 216
06 217
07 218
08 219
09 220
10 221
11 222
12 223
13 224
14 225
15 226
16 227
17 228
18 229
19 230
20 231
21 232
22 233
channel 10
or .
, use the button UP or
.
Sub - DMX Sub -
value address
23 234 45
24 235 46
25 236 47
26 237 48
27 238 49
28 239 50
29 240 51
30 241 52
31 242 53
32 243 54
33 244 55
34 245 56
35 246 57
36 247 58
37 248 59
38 249 60
39 250 61
40 251 62
41 252 63
42 253 64
43 254 65
44 255 66