Music Control; Show Programmes And Sequences Of Scenes; Programming Sequences Of Scenes; Synchronous Control Of Multiple Spotlights (Master / Slave Mode) - IMG STAGELINE PARC-56/RGB Manual De Instrucciones

have selected a storage location. The display
GB
now indicates , ,
= brightness of the colour red
= brightness of the colour green
= brightness of the colour blue
6) Use the button ENTER to select the colours one
after the other, and use the button UP or DOWN
to set their brightness.
7) To select another shade of white or to change the
settings of another storage location, press the
button MENU so that the number of the storage
location is shown again. Then repeat steps 4 – 6.
Note: If the spotlight is switched off and on again in this
mode, the spotlight will remain dark and the shade of white
desired or the individual shade of colour will have to be
selected again.

5.1.3 Music control

The spotlight is equipped with a microphone to sup-
port music-controlled colour changes and a music-
controlled stroboscope.
1) Press the button MENU repeatedly until the
highest menu level has been reached.
2) Press the button UP or DOWN repeatedly until
the display indicates
3) Press the button ENTER. The display indicates
the mode most recently selected:
= music-controlled colour change
= music-controlled stroboscope
4) Use the button UP or DOWN to select the mode
desired.
Important: Do not exit the menu item
via the button MENU if the spotlight is to
operate in a music-controlled mode after switch-off
and switch-on.
5.1.4 Show programmes and
sequences of scenes
10 show programmes (
in the spotlight. Furthermore, 10 se quences of
scenes (
be programmed (
grammes and sequences of scenes can be started
as follows:
1) Press the button MENU repeatedly until the
highest menu level has been reached.
2) Press the button UP or DOWN repeatedly until
the display indicates
3) Press the button ENTER. The display now indi-
cates the show programme most recently
selected (
scenes most recently selected (
4) Use the button UP or DOWN to select the show
programme or sequence of scenes desired.
14
and a number (0 – 255).
.
...
... ) with up to 30 scenes can
chapter 5.1.5). The show pro-
.
... ) or the sequence of

5.1.5 Programming sequences of scenes

10 sequences of scenes can be easily pro-
grammed. A sequence may consist of up to 30
scenes which is automatically repeated. For each
scene, the colour can be set along with its bright-
ness, the stroboscope function can be activated
with a variable flash frequency, and the duration of
the scene as well as the fading time can be defined.
1) Press the button MENU repeatedly until the
highest menu level has been reached.
2) Press the button UP or DOWN repeatedly until
the display indicates
3) Press the button ENTER. The display now indi-
cates the number of the sequence most recently
changed (
4) Use the button UP or DOWN to select the num-
ber under which the sequence of scenes is to be
stored, and then press the button ENTER. The
display indicates the number of the first scene
(
5) Press the button ENTER to call up the following
setting functions:
= brightness of the colour red
= brightness of the colour green
= brightness of the colour blue
= flash frequency of the stroboscope
= duration of the scene in seconds
= fading time
Use the button UP or DOWN to set the value
desired.
6) After setting the first scene, press the button
or
MENU. The display indicates the number of the
scene again. Use the button UP to select the
second scene, press ENTER and then select
the settings for this scene. Repeat this proce-
dure for the following scenes. If not all 30
scenes are required, enter 0 as the value
the numbers of scenes that are not to be used.
) are stored
5.2 Synchronous control of multiple
spotlights (master / slave mode)
Multiple PARC-56 / RGB or PARC-64 / RGB may be
connected. The master unit can then control all
slave units in sync.
1) Connect the spotlights via their DMX jacks to a
chain. Please refer to chapter 5.3.1 "DMX con-
nection", ignoring step 1.
2) The units that are to be controlled by the master
unit must be defined as slave units:
a) Press the button MENU repeatedly until the
... ).
highest menu level has been reached.
b) Press the button UP or DOWN repeatedly
until the display indicates
.
... ).
).
for
.