Temperature Indication And Overheat Control; Resetting The Spotlight To Its Factory Settings; Cleaning The Spotlight; Technical Data - IMG STAGELINE PARC-56/RGB Manual De Instrucciones

6.4 Temperature indication
and overheat control
The spotlight is equipped with an overheat control.
When the temperature inside the spotlight is too
high, the spotlight will be switched off. After cooling
down, the spotlight will be switched on again auto-
matically. To indicate the inside temperature:
1) Press the button MENU repeatedly until the dis-
play indicates
2) Press the button ENTER.
3) When is indicated, press the button
ENTER. The inside temperature will be indi-
cated in °C.
4) To exit the menu branch, press the button
MENU.
6.5 Resetting the spotlight
to its factory settings
The factory settings of the spotlight are as follows:
Function
number of DMX channels
max. brightness
white balance function
subaddress function
slow LED response
subaddress
11 shades of white
white balance
DMX / independent
mode or slave mode
To reset the spotlight to its factory settings:
1) Press the button MENU repeatedly until the
highest menu level has been reached.
2) Press the button UP or DOWN repeatedly until
the display indicates
3) Press the button ENTER. The display changes
to , , ,
4) Press the button UP or DOWN repeatedly until
the display indicates
5) Press the button ENTER so that the display indi-
cates four entry positions (. . . .). Then press the
following buttons:
UP, DOWN, UP, DOWN.
All rights reserved by MONACOR
be reproduced in any form or by any means for any commercial use.
.
Factory setting
= 10 channels
= 100 %
= slowest
01
factory settings
R = 255, G = 255,
B = 255
= DMX / inde-
pendent operation
.
, or .
.
® INTERNATIONAL GmbH & Co. KG. No part of this instruction manual may
Each time one of these buttons is pressed, an
asterisk ( ) will appear on the display.
6) To reset the settings, press the button ENTER
(the display briefly indicates
the procedure, press the button MENU.
7) To be able to control the spotlight by DMX, use
the button MENU to return to the highest menu
level.
For an independent operation, use the button
MENU to select the operating mode and then
press ENTER to activate the mode selected.

7 Cleaning the Spotlight

Clean the plastic filter in front of the LEDs at regu-
lar intervals or as required. This is the only way to
ensure that light will be radiated at maximum
brightness. Before cleaning, disconnect the
mains plug from the socket. Only use a dry, soft
cloth and a mild detergent. Then carefully wipe the
plastic filter dry.
For cleaning the other parts of the housing, only
use a dry, clean cloth. Never use any fluid, it may
leak into the spotlight and damage it.

8 Technical Data

Data protocol: . . . . . . . . . . DMX 512
Number of
DMX channels: . . . . . . . . . selectable:
Light source: . . . . . . . . . . . RGB COB LED
Power consumption
PARC-56 / RGB: . . . . . 50 W
PARC-64 / RGB: . . . . . 100 W
Beam angle: . . . . . . . . . 60°
Power supply: . . . . . . . . . . 230 V~ / 50 Hz
Power consumption
PARC-56 / RGB: . . . . . 60 VA max.
PARC-64 / RGB: . . . . . 110 VA max.
Dimensions
PARC-56 / RGB: . . . . . ∅ 185 mm × 210 mm
PARC-64 / RGB: . . . . . ∅ 220 mm × 260 mm
Weight
PARC-56 / RGB: . . . . . 2.4 kg
PARC-64 / RGB: . . . . . 2.9 kg
Subject to technical modification.
) or, to cancel
3, 4, 5 or 10
GB
19