Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
LED 12
Œ
Connections and control buttons
LED Light Effect Bar
These instructions are intended for the
installer of the light effect bar and for oper-
ators with basic knowledge in DMX control.
Please read these instructions carefully
prior to operating the unit and keep them
for later reference.
Contents
1
2
Safety Notes . . . . . . . . . . . . . . . . . 10
3
Setting into Operation . . . . . . . . . 10
ODB-1212RGBW . . . . . . . . . . . . . 11
3.2 Control connections . . . . . . . . . . . . 11
3.2.2 Master / slave mode . . . . . . . . . . . 11
4
Operation . . . . . . . . . . . . . . . . . . . 11
4.1 Standalone mode . . . . . . . . . . . . . 11
show programs . . . . . . . . . . . . . . . 12
4.3 Master / slave mode . . . . . . . . . . . . 13
4.4.2 Using subaddresses . . . . . . . . . . 13
4.5 Additional setting options . . . . . . . . 14
4.5.1 Reset to factory settings . . . . . . . 14
4.5.2 Automatic display switch-off . . . . 14
4.5.3 Key lock . . . . . . . . . . . . . . . . . . . 14
control signal loss . . . . . . . . . . . . 14
4.5.5 Reducing colour brightness . . . . 14
and the firmware version . . . . . . 14
5
Specifications . . . . . . . . . . . . . . . 14
5.1 DMX functions . . . . . . . . . . . . . . . . 14
59-channel mode . . . . . . . . . . . . 14
5.1.2 3-channel mode . . . . . . . . . . . . . 14
8-channel mode . . . . . . . . . . . . . 15
10
POWER OUT
DMX OUT
230V~
C
1 Applications and
Setup Options
The unit ODB-1212RGBW is used for ef-
fect illumination (e. g. for emitting coloured
light or for creating running light effects and
stroboscope effects); due to its weather-
proof aluminium housing, the unit is also
suited for outdoor applications. 12 extra
bright RGBW LEDs of the OSRAM brand
are used as a light source.
The unit is designed for control via a
DMX light controller (optionally 59, 11, 8, 5,
4 or 3 DMX control channels), but it is also
possible to operate the unit on its own with
a lighting colour set or with various show
programs running. In addition, multiple
ODB-1212RGBW can be interconnected
(master/slave mode) to create synchro-
nous light effects.
Use the mounting/setup brackets (C)
located on the rear side to screw the unit to
a wall or ceiling or to place it onto an even
surface. For upside-down installation on a
crossbar, two C hooks are additionally
required (e. g. PAST-1, TA- ...).
As a special feature, the unit supports
66 subaddresses when used in DMX mode
with 11 or 59 channels. Thus, it is possible
to independently control up to 66 ODB-
1212RGBW via a single DMX start address
and the maximum number of DMX-con-
trolled units possible is substantially in-
creased.
2 Safety Notes
The unit corresponds to all relevant direc-
tives of the EU and is therefore marked
with
WARNING The unit uses dangerous
G
Immediately disconnect the unit from the
mains
1. if the unit or the mains cable is visibly
damaged,
2. if a defect might have occurred after
the unit was dropped or suffered a
similar accident,
DMX IN
.
mains voltage. Leave servic-
ing to skilled personnel only;
inexpert handling of the unit
may result in electric shock.
A
B
C
3. if malfunctions occur.
In any case the unit must be repaired by
skilled personnel.
G
A damaged mains cable must only be
replaced by skilled personnel.
G
Never pull the mains cable for discon-
necting the mains plug from the socket,
always seize the plug.
G
For cleaning the housing and the protec-
tive pane in front of the LEDs, only use a
mild detergent.
G
No guarantee claims for the unit and no
liability for any resulting personal dam-
age or material damage will be accepted
if the unit is used for other purposes than
originally intended, if it is not safely
mounted, if it is not correctly connected
or operated, or if it is not repaired in an
expert way.
If the unit is to be put out of opera-
tion definitively, take it to a local
recycling plant for a disposal which
is not harmful to the environment.
3 Setting into Operation
WARNING To prevent damage to your
eyes, never look directly into
the light source for any length
of time.
Please note that fast changes in lighting
may trigger epileptic seizures with photo-
sensitive
persons
epilepsy!
Connect the plug (A) of the cable POWER
IN to the inline jack of the mains cable pro-
vided and then use the cap nut to screw the
plug-in connection together (fig. 1 shows
the completed connection).
CAUTION! If no further unit is connected to
the cables POWER OUT and DMX OUT,
make absolutely sure to screw the protec-
tive covers onto the inline jacks. The cable
POWER OUT carries mains voltage!
Connect the mains plug to a mains socket
(230 V~/ 50 Hz). The unit will be switched
on. The display will indicate the operating
mode.
POWER IN
DMX IN
LED 1
PROGRAM1
P:07S:01
M
or
persons
with
Publicidad
Capítulos
Tabla de contenido
