DSC GS2060 Manual De Instrucciones página 9

Enter [*][8][Installer Code] [Section Number] for panel programming. Record any values that are modified from their default,
in the Programming Worksheets .
NOTE: When programming Toggle
Options, the toggle is ON when the
number is dispalyed and OFF when
the number is not displayed. (e.g.,
[1---5---], Toggle Options 1 and 5
are ON, all others are OFF).
8. Panel Section [167] GPRS/Ethernet
Interface Communications Wait for
ACK: Program value as: 060 (sec-
onds).
9. When the communicator is installed
with the PC9155 panel, 4 telephone
number are available to backup one
another. You can set up these 4 tele-
phone numbers to perform in one of
two ways: Backup dialling or Alternate
dialling.
a. Backup dialling: each of the 4 tele-
phone numbers will make 5 dialling
attempts in turn, before a Failure to
Communicate (FTC) trouble is dis-
played on the keypad.
b. Alternate dialling: each telephone
number makes 1 dialling attempt and
cycles through each of the 4 num-
bers for a total of 5 times each. If all
numbers fail the 5 attempts,, an FTC
trouble is displayed on the keypad.
10. Panel Sections [301], [302], [303],
and [305] can be configured as Pri-
mary communication paths.
a. Panel Sections [302], [303], and
[305] may also be configured for
backup or redundant communica-
tions by using Panel Sections [383]
or [351] - [376]. Refer to the
PC9155 panel Installation Manual
for more information.
b. If a valid phone number is pro-
grammed, communications will use
Public Switched Telephone Network
(PSTN). Entering a 4 digit hexadecimal value for a telephone number will change the call routing as determined by the num-
ber programmed:
DCAAF: Internal (All Receivers). Signals will be routed depending on the GS/IP module programming.
DCBBF: Ethernet Receiver 1 (Primary). (TL260GS/TL265GS only).
DCCCF: Ethernet Receiver 2 (Backup). (TL260GS/TL265GS only).
DCDDF: GPRS Receiver 1 (Primary).
DCEEF: GPRS Receiver 2 (Backup).
NOTE: Add a single 'F' as a suffix to the number to populate the unused remainder of the 32 character field.
11. Panel Section [350]: If any of the phone numbers have been programmed as DCAA, DCBB, DCCC, DCDD, or DCEE, panel Sec-
tion [350] must be set to [04] if SIA format or [03] if Contact ID format.
12. Panel Section [382]: Toggle Option [5], (GS/IP Module Enabled), must be set to ON. If this option is OFF, the yellow status LED
will indicate 'Panel Supervision Trouble' (2 flashes) and the unit can not be programmed via PC-LINK cable.
13. Panel Section [401]: Toggle Option [1] must be set to ON in order to perform panel DLS session through GPRS or Ethernet.
NOTE: Keep a record of the SIM card telephone number, it is required by users for SMS interactive functions.
Due to the nature of the SIM card activation process with GSM network carriers, it can take up to 24 hours for SIM card
activation to be complete.
PC9155
Red
Wire
BATTERY
Do not disconnect the battery cable from the alarm controller board;
the battery shall be disconnected from the + (PLUS) TERMINAL.
5
Figure 4 PC 9155 Control Panel
ANTENNA
To Remove Connector -
insert small, flat head
screwdriver between cable
and the radio module then
gently pry plug loose.
NOTE: Removal with fingers
may damage the connector.
Status
LEDs
TL265GS / GS2065
SIM Card