Front Panel Overview - Numark C3 USB Guia De Inicio Rapido

FRONT PANEL OVERVIEW

6 7
5
8
4
9
3 10
2
20
1. POWER LED – Illuminates when the mixer is on.
2. MIC ON/OFF – Mutes and unmutes the
microphone signal. When muted (LED is off), the
microphone signal will not be routed to the
master mix.
3. MIC GAIN – Adjusts the volume of the
microphone input.
4. MIC BASS – Adjusts the low (bass) frequencies
of the microphone channel.
5. MIC TREBLE – Adjusts the high (treble)
frequencies of the microphone channel.
6. COMBO MICROPHONE INPUT – This "combo"
jack accepts XLR or 1/4" microphones.
7. CHANNEL GAIN – Adjusts the corresponding
channel's pre-fader audio gain.
8. CHANNEL TREBLE – Adjusts the high (treble)
frequencies of the corresponding channel.
9. CHANNEL MID
frequencies of the corresponding channel.
10. CHANNEL BASS – Adjusts the low (bass)
frequencies of the corresponding channel.
11. INPUT SELECTOR – Selects which input source
will be routed to the corresponding channel.
Select "Phono" if you would like to route audio
from a connected phono-level turntable.
Select "CD" or "Line" if you are using line-level
devices, such as CD players, samplers, etc.
Select "USB" if you would like to route audio
from a computer connected to the rear of the
mixer via USB.
Select "Mic" if would like to route audio from a
microphone connected to the rear panel.
12. CHANNEL FADER – Adjusts the audio level
sent to the Program mix.
13. CUE BUTTON – Routes the corresponding
channel (post-gain, post-EQ, and pre-channel
fader) to the Cue channel for previewing.
14. HEADPHONE VOLUME – Adjusts the volume
level of the headphone output.
11 11
7
7
13 13
8
8
9 9
12
12
10 10
19
18
– Adjusts the mid-range
11 11
7
7
13 13
8
8
9 9
12 12
10 10
19
20
15. HEADPHONE MIX – Crossfades between Cue
and Program in the Headphone channel. When
all the way to the left, only channels routed to
PFL will be heard.
the Program mix will be heard. Please note that
this control only has an effect while the SPLIT /
BLEND button is in the "Blend" position.
16. SPLIT / BLEND BUTTON – When this switch is
in the down position, the headphone audio will be
"split" such that all channels sent to CUE are
mixed to mono and applied to the left headphone
channel and the Program mix is mixed to mono
and applied to the right channel. When the switch
is in the up position, Cue and Program audio will
be "blended" together.
17. HEADPHONE
headphones to this output for previewing and
cueing.
Important: The volume should always be set at
its lowest
disconnecting headphones to prevent damage to
headphones and your hearing.
18. REPLACEABLE CROSSFADER – Blends audio
between the channels assigned to the left and
right side of the crossfader (see ASSIGN KNOB
below).
Note: The crossfader is user-replaceable if it
should ever wear out. Simply remove the
facepanel and then remove the screws holding it
in position.
authorized replacement from your local Numark
retailer only.
19. ASSIGN KNOB – Determines which channel will
be routed to either side of the crossfader.
Note: Volume levels of channels not selected will
be determined only by the individual channel
sliders.
5
11
23 26
13
1
21
12
25
25
14
15
When all the way right, only
JACK – Connect
setting while connecting
Replace the fader with a quality
24
22
16
17
your ¼"
and