Replacement Parts - OHAUS Adventurer Manual De Instrucciones

Error Codes
When a problem occurs using the balance, the display will indi-
cate an error code. Review the listed codes and follow instruc-
tions to correct the problem.
Err 2.0 Stability error. Check if balance is located near vibrat-
ing equipment or if air currents are affecting it.
Err 3.0 Calibration error (wrong mass). Incorrect or no cali-
bration mass used when performing calibration proce-
dure. Error will flash momentarily, then balance will
use previous calibration data. Recalibrate correctly.
Err 4 Invalid data checksum in type or adjust data. Return
balance for servicing.
Err 6.0 Parts counting error - Average piece weight is less than
1d. Balance shows error then exits parts counting.
Err 8.4 Over or under load. Sample being weighed exceeds
the capacity of the balance. If error occurs when the
sample is within the balance capacity, balance may be
incorrectly calibrated. An underload such as the pan
off of the balance could also display Err8.4. Recali-
brate the balance.
Err 9 Internal data error. Return balance for servicing.
Err 9.8 Invalid checksum in calibration or setup data. The
balance may need recalibration, particularly linearity
calibration. If the error persists after recalibration,
the balance must be serviced.
PARTS INFORMATION
If you require replacement parts or would like to purchase
accessories, inside the U.S., please call Ohaus Corporation
toll-free at (800) 526-0659 and from outside the U.S., (973)
377-9000. An Ohaus Product Parts Specialist will be available
to help you.
SPECIFICATIONS
Installation Category II, Polution Degree 2.
Capacity
Readability
Weighing units/modes
Repeatability (Std. Dev.)
Linearity
Tare Range
Stabilization Time (seconds)
Sensitivity Drift
Operating Temp Range
Power Requirements
Calibration
Display (in/cm)
Pan Size (in/cm)
Draft shield clearance height
above pan (in/cm)
Dimensions (WxHxD) (in/cm)
Net Wt (lb/kg)
Shipping Wt (lb/kg)
Model
Item No.
Note 1. 150g and 310g balances include a round draft shield.
Note 2. 65g and 210g analytical balances include a three door draft shield.
65g (2)(3) 210g (2)(4) 150g
0.1mg
g, kg, mg, ct, N, lb, oz, ozt, gn, dwt, momme, mesghal, 3 taels, ticals, Parts Counting
0.1mg
±0.2mg ±0.3mg
3ppm/°C
3.5/9 dia.
9.3/23.6
8.5x14.3x13.5/36.6x11x34.3 8.5x8.3x13.5/21.7x21x34.3
12.5/5.7
21/9.5
AV-65 AV-210 AV-150
AR0640 AR2140 AR1530

REPLACEMENT PARTS

AC Adapters:
US/Japan 100 V
US 100-120V
Europe 220-240V
UK 220-240V
Table version 220-240V Reqs. sep. line cord, Aus. 11103745
Line cord for above
Table version 220-240V Reqs. sep. line cord, US
Line cord for above
Euro/Germany, Belgium, France 220-240V
Pan for 65g, 210g
Pan for 150g, 310g,
Pan for 510 to 4100g,
ACCESSORIES
20g Calibration Mass
50g Calibration Mass
100g Calibration Mass
200g Calibration Mass
500g Calibration Mass
1kg Calibration Mass
2kg Calibration Mass
Security Device
Impact printer
In-Use Cover
Scoops:
Aluminum, 3.62 x 4.50 x 1.0"/
9.20 x 11.34 x 2.54 cm
Black anodized, aluminum, 3.62 x 4.50 x 1.0"/
9.20 x 11.34 x 2.54 cm
Aluminum, 1.5 x 2.00 x 0.43"/
3.81 x 5.08 x 1.11 cm
Gold anodized aluminum, 2.25 x 3.00 x 0.75"/
5.71 x 7.62 x 1.90 cm
(1) 310g (1) 510g
0.001g
0.001g
±0.002g ±0.01g
Full capacity by subtraction
3 Seconds
50° to 86° F/10° to 30° C
8 - 14.5V 50/60Hz 6VA or 9.5 - 20V 6W
External Digital
LCD (1.2/3 high)
3.9/10 dia.
6.8/17.25
10/4.5
16/7.3
AV-130 AV-510
AR3130 AR5120
Note 3. 65g balances do not contain lb and kg units.
Note 4. 210g balances do not contain lb, kg, ct and dwt units.
5
11103743
11103741
11103740
11103742
11103745
11103744
3.5 (9.0cm) dia. 12106739
3.9" (10cm) dia. 12104912
7.1" (18cm) 12104937
AS142 -02
400302-010
1500g 3100g
0.01g
0.01g
±0.02g
10ppm/°C
7.1/18 dia.
..............
8.5x4.3x13.5/21.7x11x34.3
8.5/3.9
14/6.4
AV-1500 AV-3100 AV-4100
ARA520 ARC120
Part No.
76199-01
6569-00
Part No.
49024-11
49054-11
49015-11
49025-11
49055-11
49016-11
49026-11
76288-01
4590-10
4590-30
5076-00
5077-00
4100g
0.1g
0.1g
±0.1g
ARD110