Measuring Tool Power Supply - Bosch GLL Professional Serie Manual Original

Line lasers
– Compatibility
– Operating system
Weight according to EPTA-Procedure 01:2014
– with rechargeable battery
– with non-rechargeable batteries
Dimensions (length × width × height)
Protection rating
Permitted ambient temperature
– during charging
– During operation F)
– during storage
Recommended batteries
Recommended chargers
A) The working range may be reduced by unfavourable environmental conditions (e.g. direct sunlight).
B) Only non-conductive deposits occur, whereby occasional temporary conductivity caused by condensation is expected.
C) Shorter operating times in Bluetooth® operation and/or in conjunction with RM 3.
D) When using Bluetooth® Low Energy devices, it may not be possible to establish a connection depending on the model and operating system.
Bluetooth® devices must support the SPP profile.
E) The signal range may vary greatly depending on external conditions, including the receiving device used. The Bluetooth® range may be signi-
ficantly weaker inside closed rooms and through metallic barriers (e.g. walls, shelving units, cases, etc.).
F) Limited performance at temperatures <0 °C
Technical data determined using the battery that comes with the product.
The serial number (19) on the type plate is used to clearly identify your measuring tool.
Assembly

Measuring Tool Power Supply

The measuring tool can be operated either with conventional
non-rechargeable batteries or with a Bosch lithium-ion bat-
tery.
Operation with Rechargeable Battery
Use only the chargers listed in the technical data. Only
u
these chargers are matched to the lithium-ion battery of
your measuring tool.
Note: The use of batteries unsuitable for your measuring tool
can lead to malfunctions or damage to the measuring tool.
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the Electronic Cell Protection (ECP). A protective circuit
switches the measuring tool off when the battery is drained.
Bosch Power Tools
GLL 3‑80 C
Bluetooth® 4.0 (Low Energy)
Android 4.3 (and above)
iOS 7 (and above)
0.90 kg
0.86 kg
162 × 84 × 148 mm
IP 54 (dust- and splash-proof)
0 °C to +45 °C
–10 °C to +40 °C
–20 °C to +70 °C
GBA 10,8V ...
GBA 12V ... (except GBA 12V 4.0 Ah)
AL 11.. CV
GAL 12.. CV
Do not switch the measuring tool back on after it has
u
been switched off by the protective circuit. This can
damage the battery.
To insert the charged battery (15), slide it into the battery
bay (10) until you feel it engage.
To remove the battery (15), press the release buttons (13)
and pull it out of the battery bay (10). Do not use force to
do this.
Operation with Non-Rechargeable Batteries
It is recommended that you use alkaline manganese batter-
ies to operate the measuring tool.
The batteries are inserted into the battery adapter.
The battery adapter is intended only for use in desig-
u
nated Bosch measuring tools and must not be used
with power tools.
To insert the batteries, slide the cover (11) of the battery
adapter into the battery bay (10). Place the batteries into
the cover as per the illustration on the sealing cap (14).
Slide the sealing cap over the cover until you feel it click into
place.
English | 19
GLL 3‑80 CG
D) Bluetooth® 4.0 (Low Energy)
Android 4.3 (and above)
iOS 7 (and above)
162 × 84 × 148 mm
IP 54 (dust- and splash-proof)
0 °C to +45 °C
–10 °C to +40 °C
–20 °C to +70 °C
GBA 10,8V ...
GBA 12V ... (except GBA 12V 4.0 Ah)
GAL 12.. CV
1 609 92A 4F2 | (06.06.2018)
D)
0.90 kg
0.86 kg
AL 11.. CV