Makita GD0800C Manual De Instrucciones página 5

FUNCTIONAL DESCRIPTION
CAUTION:
• Always be sure that the tool is switched off and
unplugged before adjusting or checking function on the
tool.
Switch action (Fig. 1)
CAUTION:
• Before plugging in the tool, always check to see that
the slide switch actuates properly and returns to the
"OFF" position when the rear of the slide switch is
depressed.
To start the tool, slide the slide switch toward the "I (ON)"
position. For continuous operation, press the front of the
slide switch to lock it.
To stop the tool, press the rear of the slide switch, then
slide it toward the "O (OFF)" position.
Speed adjusting dial (Fig. 2)
The tool speed can be changed by turning the speed
adjusting dial to a given number setting from 1 to 5.
Higher speed is obtained when the dial is turned in the
direction of number 5. And lower speed is obtained when
it is turned in the direction of number 1.
Refer to the table for the relationship between the num-
ber settings on the dial and the approximate tool speed.
GD0800C
–1
Number min (RPM)
1 – 2 7,000 – 10,000
2 – 3 10,000 – 17,000
3 – 4 17,000 – 24,000
4 – 5 24,000 – 28,000
006478
CAUTION:
• If the tool is operated continuously at low speeds for a
long time, the motor will get overloaded, resulting in
tool malfunction.
• The speed adjusting dial can be turned only as far as 5
and back to 1. Do not force it past 5 or 1, or the speed
adjusting function may no longer work.
ASSEMBLY
CAUTION:
• Always be sure that the tool is switched off and
unplugged before carrying out any work on the tool.
Installing the side handle (Fig. 3)
Always use the side handle to ensure operating safety.
Install the side handle on the tool barrel, then tighten the
handle by turning clockwise at the desired position.
Installing or removing wheel point (Fig. 4 & 5)
Loosen the collet nut and insert the wheel point into the
collet nut. Use the smaller wrench to hold the spindle and
the larger one to tighten the collet nut securely.
The wheel point should not be mounted more than 8 mm
from the collet nut. Exceeding this distance could cause
vibration or a broken shaft.
To remove the wheel point, follow the installation proce-
dure in reverse.
CAUTION:
• Use the correct size collet cone for the wheel point
OPERATION
Turn the tool on without the wheel point making any con-
tact with the workpiece and wait until the wheel point
attains full speed. Then apply the wheel point to the
workpiece gently. To obtain a good finish, move the tool
in the leftward direction slowly.
CAUTION:
• Apply light pressure on the tool. Excessive pressure on
MAINTENANCE
CAUTION:
• Always be sure that the tool is switched off and
• Never use gasoline, benzine, thinner, alcohol or the
To maintain product SAFETY and RELIABILITY, repairs,
carbon brush inspection and replacement, any other
maintenance or adjustment should be performed by
Makita Authorized Service Centers, always using Makita
GD0810C
replacement parts.
–1
min (RPM)
OPTIONAL ACCESSORIES
1,800 – 2,400
CAUTION:
2,400 – 4,100
• These accessories or attachments are recommended
4,100 – 5,800
5,800 – 7,000
If you need any assistance for more details regarding
these accessories, ask your local Makita service center.
• Wheel points
• Collet cone set (3 mm, 6 mm, 1/4", 1/8")
• Vise holder
• Wrench 13
• Wrench 19
• Side handle set
NOTE:
• Some items in the list may be included in the tool pack-
which you intend to use.
(Fig. 6)
the tool will only cause a poor finish and overloading of
the motor.
unplugged before attempting to perform inspection or
maintenance.
like. Discoloration, deformation or cracks may result.
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
age as standard accessories. They may differ from
country to country.
5