Before Starting The Equipment - EINHELL TC-TS 315 U Manual De Instrucciones Original

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
•
Unpack the bench-type circular saw and
check it for damage which may have occurred
in transit.
•
The machine has to be set up where it can
stand firmly, e.g. on a work bench, or it must
be bolted to a strong base.
•
All covers and safety devices have to be pro-
perly fitted before the machine is switched on.
•
It must be possible for the saw blade to run
freely.
•
When working with wood that has been pro-
cessed before, watch out for foreign bodies
such as nails or screws etc.
•
Before you actuate the On/Off switch, make
sure that the saw blade is correctly fitted and
that the machine's moving parts run smoothly.
6. Assembly
Danger! Pull out the power plug before carry-
ing out any maintenance, resetting or assem-
bly work on the circular saw!
6.1 Assembly of the sub-frame and table
length extension (Figs. 1, 3a-g)
Danger! Make allowance for the weight of the
machine and arrange another person to help you
if necessary!
•
Turn the bench-type circular over and set the
saw down on the floor or on some other work
surface. Important! Place suitable material
(e.g. packaging material) between the table
surface and the surface on which it is stood to
prevent any damage to the table surface.
•
Use the hexagon screws (32), washers (35),
spring washers (36) and nuts (38) to screw
the legs (29) loosely to the saw table (1).
•
Use the hexagon screws (32), washers (35),
spring washers (36) and nuts (38) to screw
the cross struts (30) and longitudinal struts
(31) loosely to the legs. Make sure that the
holes in the fitted cross struts face upwards to
enable the table length extension to be fitted
later. Also make sure that the tongue-and-
Anl_TC_TS_315_U_SPK9.indb 31 Anl_TC_TS_315_U_SPK9.indb 31
GB
groove connection between the strut and leg
engages properly.
•
Use the hexagon screws (32), washers (35),
spring washers (36) and nuts (38) to screw
the rubber feet (13) securely to the legs.
•
Fasten the extractor adapter (16) to the ma-
chine using the screws (49). Important! The
side connection socket of the extractor adap-
ter (16) must be pointing to the right.
•
Use the hexagon screws (32), washers (35),
spring washers (36) and nuts (38) to screw
the table length extension (39) to the saw tab-
le (1).
•
Use the hexagon screws (32), washers (35),
spring washers (36) and nuts (38) to screw
the struts (43) to the table length extension
(39) and the rear cross strut (30).
•
Turn the machine over so that it stands on
its legs. The machine must be stood on a flat
surface. Then tighten all loose screw connec-
tions.
6.2 Assembling the handles, tool hook and
chassis (Figs. 1, 4a-d)
•
Use the hexagon screws (32), washers (35),
spring washers (36) and nuts (38) to screw
the handles (42) to the front legs.
•
Screw the tool hook (34) to the front right leg.
Important! When not in use, the face spanner
(33), ring wrench (37), push stick (3) and
push block (10) can be kept on the tool hook
(34).
•
Use the hexagon screws (32), washers (35),
spring washers (36) and nuts (38) to screw
the chassis (21) to the rear legs.
•
Caution! Select a distance for the tires relative
to the ground using the oval hole in the chas-
sis (21) which ensures that the machine does
not have to be lifted too high when transpor-
ted by the user
•
Fit the short guide rail for the parallel stop
(28) to the front of the saw table (1) (see Fig.
4e); and the long guide rail for the cross stop
(41) to the left side of the saw table (1) (see
Fig. 4f).
•
To do so, first fasten the screw (32), washer
(35), spring washer (36) and nut (38) loosely
in the two holes in the saw table. The head of
the screw must be on the outside of the saw
table (1) without a washer.
•
Now slide the guide rail (28) with the groove
over the two screw heads as shown in Fig. 4g
until the right end of the guide rail (28) is flush
with the right side of the saw table (1).
•
Fit the long guide rail for the cross stop (41)
- 31 -
23.03.2020 09:09:28 23.03.2020 09:09:28