Miche REVOX Manual De Uso página 5

GB
Section I: General indications
Section II: Hubs
Section III:
Spokes
Section IV:
Complete wheels
Section V: Installing the clincher tire
Section VI: Fitting of Vibrostop
SECTION I:
General indications
We thank you for buying the REVOX RC wheels set a product that
will guarantee your security and functionality through the years.
Before proceeding with using the wheels, please read carefully the
following instruction and store them in a safe place for eventually
reusing.
Fac Michelin Srl reserve to modify the content of this manual
without notice. The updated version will always be available www.
michetechnology.com
On our website you will also find information on the other Miche or
Supertype products and the spare parts catalogue.
In the box of REVOX wheel set you will find:
• The font and the rear wheel
• The quick release set
• A set of sintered brake pads for carbon rims
• Wheel bag
• Rim tapes
• Vibrostop
• The manual of instructions and use of Wheels
• Elastic wheel protection
Attention
Any modification or alteration (and graphic) of the
product with non-original spare parts or spare parts
not delivered directly by Fac Michelin Srl, involves the
expiration of the guarantee.
Direct and violent impacts on broken road surfaces can
cause damage to the rims. Such damage is outside the
conditions of our guarantee and repair costs will be
charged directly to the customer.
In case of strange impact caused from bad road base or
wheels transport, we trust to bring the wheels to your
mechanic for a check.
Using only MICHE brake pads for carbon rim that you
find inside wheel set box. Use original spare parts
exclusively provided by Fac Michelin Srl
Warning
• Check for proper operation and state of wear of all the coBefore
using the bicycle it is necessary to:
•Check for proper operation and state of wear of all the
components before starting to ride.
• Check the condition and pressure of the tyres fitted to your
Miche wheels. Pressure must not exceed the limit of 8bar
and 116psi signed behind valve hole. The inflating pressure
of the tyres must NOT exceed the LOWER pressure level between
the maximum pressure stated by the tyre manufacturer.
Excessive tire pressure reduces the grip of the tire on the road and
increases the risk that the tire will unexpectedly burst.
Inflation pressure that is too low reduces tire performance and
increases the probability of sudden and unexpected loss of tire
MAIN INDEX
pressure. In addition, premature damage to the rim may occur.
Incorrect tire pressure could cause tire failure or loss of control of
the bicycle, resulting in an accident, personal injury or death.
• Check your wheel(s) spoke tension, to ensure there are no
spokes with low spoke tension. In the event
of any spokes not being at the correct tension please note that
any spoke tension adjustments must be carried out by a specialist
skilled cycle mechanic.
• Check that the wheel quick release are correctly closed to
ensure the wheels are held in the cycle frame correctly, see (fig. 6)
ATTENTION incorrect use or the loosening of the quick
release could lead to a serious or fatal accident.
• Check very carefully the alignment of the front and rear brake
calliper brake blocks, ensuring the break only on the correct braking
surface of the Miche wheel rim(s) also check for, and remove, any
foreign particles which may be imbedded in the break pad. Check
wear status regularly of the rim and replace it if necessary. Rims
can be considered faulty when braking surface appear
to be small signs, cracks and other signs deeper than
0,2mm. To maintain the brake pads are in efficient working order
and to avoid wear on the sides of the rims, you should remove with a
file any residue of sand, debris or foreign objects which may become
embedded in the brake pads, especially during use in the rain.
• When riding in wet conditions, remember that the stopping
power of your brakes is greatly reduced and the adherence of
the tires to the ground is considerably reduced. This makes it
harder to control and stop your bicycle in wet conditions to avoid
an accident. An accident could results in severe personal
injury or death.
• To the users of more than 85kg weight, Fac Michelin suggests
to check the wheels status to the mechanic every two months or
every 1,500km.
• Never wash the pieces with pressure-fed water because water
may get through the seals and cause permanent damage to the
internal components. We recommend washing components with a
sponge, mild soap, and water.
• Salt water environments (as found on winter roads and neat the
seaside) can cause galvanic corrosion on most bike parts. Carefully
rinse, clean, dry and re-lubricate all exposed parts to avoid damage,
malfunctions and accidents.
SECTION II:
Warning
If you have any doubt whatsoever your service-repair
ability, please take your bicycle to a qualified repair
shop.
Before any maintenance operations on your wheels,
always wear gloves and protection glasses.
Use original spare parts exclusively provided by Fac
Michelin S.r.l.
When replacing any broken sealed bearings please ensure sealed
bearing correct measure and specification are used.
5
Hubs manteinance