Operating Principle; Preparation; Working With The Battery-Operated Clipping Machine, Charger And Lithium Ion Battery; System Set-Up - B.Braun Aesculap Econom CL Instrucciones De Manejo

Aesculap®
Econom CL/Econom CL Equipe/Econom CL Fitter cattle and horse clipping machine

2.4 Operating principle

Battery-operated clipping machine Econom CL/Econom CL Equipe/
Econom CL Fitter
The battery-operated clipping machine Econom CL/Econom CL Equipe/
Econom CL Fitter is switched on and off using the on/off button 36.
Note
The on/off button only reacts after >0.5 s in order to avoid the machine
being switched on or off unintentionally.
Charger GT803/Li-ion battery GT801
The charger GT803 is designed for a mains voltage/frequency range of
100 V to 240 V and 50 Hz to 60 Hz.
To make the charger GT803 ready for operation, connect it to mains power
by plugging in the mains plug.
The charger GT803 is equipped with one charging bay.
Charging starts automatically as soon as the Li-ion battery is inserted in
the charging station.
The charging time depends on the charge state and capacity of the Li-ion
battery.
Charging principle
The Li-ion batteries are charged by constant current pulses.
The charge state of the Li-ion battery is monitored during charging.
Monitoring of the charging curve ensures that the battery is fully charged
without overcharging.
Additionally, the battery temperature and charging time are monitored as
well.
The charge status display d of the lithium ion battery has 5 LEDs. Each LED
stands for 20 % of charge volume. When the battery is charging, the LED
of the respective charging status blinks. When all the LEDs are
permanently illuminated, the battery is completely charged.
Charging time
Charging is stopped as soon as the maximum charging time is reached. The
charging time is approx. 70 min.

3. Preparation

Non-compliance with the following rules will result in complete exclusion
of liability on the part of Aesculap.
Always observe the following guidelines when setting up and
operating the product:
– national regulations for installation and operation,
– the national regulations on fire and explosion protection,
– operating advisories according to IEC-/VDE regulations.
4
4. Working with the battery-operated
clipping machine, charger and lithium
ion battery

4.1 System set-up

Connecting the accessories
Combinations of accessories that are not mentioned in the present
instructions for use may only be employed if they are specifically intended
for the respective application, and if they do not compromise the
performance and safety characteristics of the products.

4.2 Function check

Battery-operated clipping machine Econom CL/Econom CL Equipe/
Econom CL Fitter
Carry out a visual inspection.
Ensure that the airfilter 37/38 is positioned correctly, see Fig. G.
Push the lithium ion battery 39 into the machine shaft and lock it.
Check if the battery is charged-up: Press button e, see Fig. F.
The charge status display d indicates the charge status.
Note
In order to prevent the lithium iron battery discharging when the machine
is not being used, the electronic connection between the lithium ion
battery and the control system for the battery-operated clipping machine
is cut after 1 hour.
Reactivating the lithium ion battery 39: Press button e, see Fig. F.
All the LEDs in the charge status display d illuminate.
Charger/Li-ion battery
Carry out a visual inspection.
Prior to connecting the product to mains power:
– Check the mains power cord for any damage.
– Check the product for any damage (e.g. bent contacts of the charging
bay).
Plug in mains power cord at the device socket of the charging station.
Plug in the mains plug at the mains power socket.
Place the lithium lithium iron battery 39 in the charging bay of the
charger and charge it, see Fig. F.