The Zeppelin Air Indicator; Joining Wireless Networks And Configuring Itunes; Set Up With Mac Or Pc; Configuring Itunes - Bowers & Wilkins Zeppelin Air Manual De Instrucciones

4. The Zeppelin Air Indicator

The Zeppelin Air indicator illuminates in a range of
colours to indicate different operational conditions.
Table 1 describes the colours and their meanings.
5. Joining Wireless Networks and

configuring iTunes

In order to play your iTunes music on your Zeppelin
Air using AirPlay, your Zeppelin Air must join the
same network as the computer on which iTunes
is installed and running. Zeppelin Air network
addressing is set to DHCP which means that once it
has joined the wireless network it will not require any
further configuration. You will need to know your
home wireless network name and password
(also known as wireless key) before you start.
5.1 Set up your Zeppelin Air with your iOS
device (iPod touch, iPad or iPhone)
• Get 'Bowers & Wilkins Control' App from the
App Store or by visiting www.bowers-wilkins.
com/control
• Follow the onscreen instructions.

5.2 Set up with Mac or PC

• Get 'Bowers & Wilkins Control' App from the
App Store or by visiting www.bowers-wilkins.
com/control
• Follow the onscreen instructions.
5.3 Setting up Zeppelin Air using a wired
connection
To set up Zeppelin Air to join your wireless network
you should first connect it physically to the Mac/PC
using an Ethernet cable. You will need to ensure that
your Mac/PC wireless capabilities are disabled. Once
connected you can browse to the Zeppelin Air setup
page. Follow the steps described below.
Note: Zeppelin Air can also use a wired network
for AirPlay streaming.
• Unplug every cable from the Zeppelin Air and
undock any docked iPod or iPhone.
• Using an Ethernet cable connect the Zeppelin
Air rear panel ETHERNET socket to an Ethernet
socket on the computer.
• Connect the power cable. Zeppelin Air will switch
on with the indicator pulsing red.
• Once the Zeppelin Air indicator begins to flash
yellow. Press and hold the '+' volume button on
Zeppelin Air for 4 seconds. Zeppelin Air's indicator
will show solid purple once the wired network
connection is established.
• Using an internet browser application running
on the computer connected to the Zeppelin Air
type the Zeppelin Air default network address
(http://169.254.1.1) in the browser address field
and press "return". This will open the Zeppelin Air
setup page.
• The setup page provides the option to change the
Zeppelin Air name. Changing the name is useful
if more than one Zeppelin Air is to be connected
to the network. Enter a new name (Zeppelin Air
Kitchen for example) in the Name box.
• Select your home network Name from the
drop down list and enter the Password in the
appropriate box. Take care to type the password
correctly.
• When you are finished, click on the Apply button,
then close the Zeppelin Air setup page. Disconnect
the Ethernet cable.
• The Zeppelin Air indicator will change to steady
purple when the wireless network connection is
established. This will take up to 3 minutes.
Note: If Zeppelin Air fails to connect to your
home wireless network, the most likely fault is
an incorrectly entered network password. Follow
the reset instructions in Section 8 and begin the
network setup procedure again.
5.4 Configuring iTunes
With Zeppelin Air connected to your home network
(wired or wireless) you can configure iTunes to use it
as an output device. Select Zeppelin Air as an output
option in the pop-up AirPlay menu.
iTunes will now play through the Zeppelin Air.
Multiple Zeppelin Air units can be connected to
the wireless network and used to provide audio
in separate rooms. Each will be available in the
iTunes devices menu, identified by either the names
specified in the setup page, or by default the last
three digits of their serial numbers.
Indicator Colour
Off
Dim Red
Pulsing Red
Flash Red twice
Blue
Fast flashing Blue
Green
Fast flashing Green
Orange
Fast flashing Orange
Slow flashing Orange
Purple
Fast flashing purple
Slow flashing purple
Fast flashing Red
Slow flashing Yellow
White
Flashing white
Table 1
Indicator colour and meaning
Meaning
Standby
Sleep
Powering up
Reset started
On
Volume adjustment
On
Volume adjustment
On
Volume adjustment
Digital audio lock error
On
Volume adjustment
No network connected
Invalid operation
Wireless setup mode
Firmware update
Firmware error
Input Selected
N/A
N/A
N/A
N/A
Dock
Dock
USB
USB
Aux
Aux
Aux
AirPlay
AirPlay
AirPlay
Any
N/A
N/A
N/A
7