Designated Use; Intended Purpose; Technical Data; Equipment - Kerbl constanta4 Instrucciones De Uso

Ocultar thumbs Ver también para constanta4:
Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 35

2. Designated use

2.1 Intended purpose

The clipper is exclusively intended for clipping sheep or llamas. Any other use, in particular on humans, is explicitly prohibited.

2.2 Technical data

Type designation: . . . . . . . . . . . . . . . Constanta4-S
Supply voltage: . . . . . . . . . . . . . . . . . 230 V AC
Motor rating: . . . . . . . . . . . . . . . . . . 400 W
Frequency: . . . . . . . . . . . . . . . . . . . . 50/60 Hz
Dimensions (W/H/L): . . . . . . . . . . . . . 6 x 10 x 34 cm
Weight without cable: . . . . . . . . . . . . 1510 kg
Sound pressure level: . . . . . . . . . . . . 87 dB (A)
Strokes: . . . . . . . . . . . . . . . . . . . . . . . 2400/ min
Protection class: . . . . . . . . . . . . . . . . II
Operating conditions
Max. ambient temperature: . . . . . . . 0 – 40° C
Max. air humidity: . . . . . . . . . . . . . . . 10 – 90 % (relative)

2.3 Equipment

1 clipper with clipper head, 1 set of shear blades (mounted), 1 bottle of oil SAE 30 HD (100 ml), 1 screwdriver, 1 operating manual
and 1 storage case

3. Initial commissioning

3.1 Inspection and operating instructions

The inappropriate use of electrical devices, in particular animal breeding devices, is dangerous! Therefore, observe the following, accident
prevention measures before starting the machine.
• Never switch the machine on without properly mounted clipping plates • The volt specification on the rating plate must correspond to the
mains voltage. The machine may only be operated with AC • Avoid any contact with the moving blades • Always pull the power supply plug
out prior to maintenance work! Do not touch the blade area, even if the machine is switched off, as long as the machine is connected to the
current supply • Always place machine on a dry surface and store in dry rooms • Avoid any contact with a machine, which is in contact with
liquids. Never clip wet animals. Liquids that have penetrated into the machine reduce the electrical insulation. There is the imminent danger
of an electric shock or short-circuit. Only clean the machine with a dry cloth and a paint-brush or brush • A cable lying on the floor can get
caught and be dangerous. Lay the cable carefully and safely before clipping. Prevent the clipper connection cable from kinking or tangling.
Ensure that animals do not stand on the cable, walk over it or get caught. Keep the cable away from hot surfaces. Never wind the cable
around the machine. This can result in insulation damage and cable break. Examine the cable regularly for defects • Set the machine switch
to off (fig. 1, pos. 1, position 0) before pulling the plug from the mains • Do not use damaged shear blades with broken off teeth.Only
use sharp shear blades. Only use the original shear blades • Never insert an item into an opening of the machine. The machine noise can
disturb animals. A kick or the weight of the animal can result in substantial injuries. Therefore fixate the animal sufficiently. • Animals should
only be clipped, when unauthorised persons do not have access to the clipping location • Only clip in well-ventilated rooms and never in the
proximity of explosive materials.
These safety notes must be observed in all cases!
21

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

1899318999

Tabla de contenido