Blackstar Amplification ONE 100 Serie Manual De Instrucciones página 7

22. Power Indicator Light
The power indicator will light when the amplifier is switched on.
23. Standby
This switch applies the H.T. (High Tension) voltage required to produce sound to the
output stage. Always turn this switch on at least 30 seconds after the Power switch
(24). During short breaks in playing use just this switch to turn 'off' and 'on' the
amplifier's output.
24. Power
This switch is used to turn the amplifier on and off. You should always turn this switch
on before turning on the Standby switch (23).
MIDI Channel Switching
The Series One offers the ability to control channel selection via MIDI Program
Change messages and interfacing with most MIDI controllers is a straight forward
process. The Series One can be placed in a MIDI chain allowing you to
simultaneously select a channel on the amplifier and change the patch on a MIDI
effects processor connected to the effects loop. There are 128 available Program
Changes, giving you the possibility to access a vast number of tonal combinations.
To set-up MIDI channel switching, simply connect the MIDI controller's MIDI Out
socket to the MIDI In socket on the rear of the amplifier. The controller should be set
to transmit Program Change messages (this is usually the case). From new, a Series
One amplifier is set to OMNI mode and responds to Program Change messages on
all MIDI channels. Changing 'patches' on the controller will change the selected
channel on the amp. The default settings for each Program Change number are
shown in the table below:
Program Channel
Change
1 BRIGHT CLEAN 33 BRIGHT CLEAN
2 WARM CLEAN 34 WARM CLEAN
3 CRUNCH 35 CRUNCH
4 SUPER CRUNCH 36 SUPER CRUNCH
5 BRIGHT CLEAN 37 BRIGHT CLEAN
6 WARM CLEAN 38 WARM CLEAN
7 CRUNCH 39 CRUNCH
8 SUPER CRUNCH 40 SUPER CRUNCH
9 BRIGHT CLEAN 41 BRIGHT CLEAN
10 WARM CLEAN 42 WARM CLEAN
11 CRUNCH 43 CRUNCH
12 SUPER CRUNCH 44 SUPER CRUNCH
13 BRIGHT CLEAN 45 BRIGHT CLEAN
14 WARM CLEAN 46 WARM CLEAN
15 CRUNCH 47 CRUNCH
16 SUPER CRUNCH 48 SUPER CRUNCH
17 BRIGHT CLEAN 49 BRIGHT CLEAN
18 WARM CLEAN 50 WARM CLEAN
19 CRUNCH 51 CRUNCH
20 SUPER CRUNCH 52 SUPER CRUNCH
21 BRIGHT CLEAN 53 BRIGHT CLEAN
22 WARM CLEAN 54 WARM CLEAN
23 CRUNCH 55 CRUNCH
24 SUPER CRUNCH 56 SUPER CRUNCH
25 BRIGHT CLEAN 57 BRIGHT CLEAN
26 WARM CLEAN 58 WARM CLEAN
27 CRUNCH 59 CRUNCH
28 SUPER CRUNCH
60 SUPER CRUNCH
29 BRIGHT CLEAN 61 BRIGHT CLEAN
30 WARM CLEAN 62 WARM CLEAN
31 CRUNCH 63 CRUNCH
32 SUPER CRUNCH 64 SUPER CRUNCH
12
65 BRIGHT CLEAN 97 BRIGHT CLEAN
66 WARM CLEAN 98 WARM CLEAN
67 CRUNCH 99 CRUNCH
68 SUPER CRUNCH 100 SUPER CRUNCH
69 BRIGHT CLEAN 101 BRIGHT CLEAN
70 WARM CLEAN 102 WARM CLEAN
71 CRUNCH 103 CRUNCH
72 SUPER CRUNCH 104 SUPER CRUNCH
73 BRIGHT CLEAN 105 BRIGHT CLEAN
74 WARM CLEAN 106 WARM CLEAN
75 CRUNCH 107 CRUNCH
76 SUPER CRUNCH 108 SUPER CRUNCH
77 BRIGHT CLEAN 109 BRIGHT CLEAN
78 WARM CLEAN 110 WARM CLEAN
79 CRUNCH 111 CRUNCH
80 SUPER CRUNCH 112 SUPER CRUNCH
81 BRIGHT CLEAN 113 BRIGHT CLEAN
82 WARM CLEAN 114 WARM CLEAN
83 CRUNCH 115 CRUNCH
84 SUPER CRUNCH 116 SUPER CRUNCH
85 BRIGHT CLEAN 117 BRIGHT CLEAN
86 WARM CLEAN 118 WARM CLEAN
87 CRUNCH 119 CRUNCH
88 SUPER CRUNCH 120 SUPER CRUNCH
89 BRIGHT CLEAN 121 BRIGHT CLEAN
90 WARM CLEAN 122 WARM CLEAN
91 CRUNCH 123 CRUNCH
92 SUPER CRUNCH 124 SUPER CRUNCH
93 BRIGHT CLEAN 125 BRIGHT CLEAN
94 WARM CLEAN 126 WARM CLEAN
95 CRUNCH 127 CRUNCH
96 SUPER CRUNCH 128 SUPER CRUNCH
Program Change Assignment
To change the default assignments and set the amp up to respond to a different set
of Program Changes:
1. The amp must be powered on with either the Standby switch set to on, a jack
in the Input socket, or both.
2. Send the appropriate Program Change message to the amp.
3. Press and hold in the appropriate front panel Channel Select switch for 2
seconds.
The corresponding channel will be selected and its LED will flash three times in quick
succession to indicate it has been assigned to the last received Program Change.
The amplifier will now remember the selection. Repeat the operation until all your
Program Changes have the desired amp channel assigned to them.
MIDI Receive Channel Selection
As mentioned previously, the default mode is set to OMNI and will respond to MIDI
Program Changes on all MIDI channels. You may wish to set the amp to respond to
Program Changes on just a single MIDI channel. The Series One can be set to
respond in this way for any of the first seven MIDI channels as follows:
1. The unit must be in standby (Power (24) on and Standby (23) off), and no lead
connected to the Input jack.
2. Simultaneously press and hold the Bright Clean (3) and Crunch (9) Select
switches.
3. After 2 seconds the LED for Super Crunch (10) will begin to flash continuously
(2 flashes per second) to indicate that the unit is in MIDI Receive Channel
Program Mode.
4. Release the Bright Clean (3) and Crunch (9) Select switches and select the
required MIDI channel by using the Channel Select switches as shown in the
table below:
Bright Clean Warm Clean Crunch
OFF OFF OFF
ON OFF OFF
OFF ON OFF
ON ON OFF
OFF OFF ON
ON OFF ON
OFF ON ON
ON ON ON
The corresponding Channel Select LEDs will illuminate to show the selection and
each press of the Channel Select switches will toggle the state of its associated
LED.
MIDI CHANNEL
OMNI
1
2
3
4
5
6
7
13