JOCCA 6643 Manual De Instrucciones página 14

26-E
for your electrical installation.
-If you detect that the power supply cable, the plug or the adaptor are damaged or
have fallen into water or any other liquid, do not use the appliance, replace the
cable, the plug, or the adaptor. Go directly to the authorised JOCCA technical ser-
vice where they will replace it correctly for you.
-Never leave the appliance cable hanging.
-Do not immerse the appliance or any part of it in water or any other liquid.
-Do not pull the cable to unplug the appliance from the mains, always pull from the
plug.
-If your appliance has been dropped or fallen into water or any other liquid do not
use it or try to repair it. Take it to the JOCCA technical service.
-For your safety and for the appliance to work correctly, always use JOCCA spare
parts and accessories.
-We advise against the use of adapters, plugs and/or extension cables. If these
elements are essential, only use single or multiple adapters and extension cables
that respect the applicable safety standards, making sure that the power limit indi-
cated on the adapter and/or the extension cable is not surpassed.
-Do not move the appliance when it is in use.
-This machine should be used on a dry horizontal flat surface.
-Completely un roll the power cable to avoid overheating.
-This appliance will be completely switched off when it is unplugged from the
mains.
-When you use this machine pay a lot attention to the needle and hand wheel,
never push the bobbin or needle.
WARNING: Switch the machine off and unplug the adapter in the following
cases:
- Whilst you are carrying out activities such as threading, changing needle or chan-
ging bobbin.
- Whilst you are changing parts or preparing the fabric.
- If you finish using it.
- During a cut in electricity supply.
INSTRUCTIONS FOR USE
HOW TO START TO SEW
-In order to start the machine you need to connect the adaptor provided. Please
unwrap the adaptor and connect one end to the mains electricity supply and the
other end to the sewing machine as indicated in Figure 1. The pilot light will then
light up indicating that the machine is connected to the
mains electricity supply.
-The pedal should then be connected to the machine.
Please see Figure 1, and then you can begin to sew by
pressing down on the same.
-The sewing machine is supplied with the needle already
threaded and a small piece of cloth.
fig.1
-When you wish to begin sewing the following steps should be taken:
1.Lift up the presser foot using the lever ( nº8)
2.Lift the needle up manually to its highest point. To do this turn the manual wheel
(nº 11) in the direction indicated by the arrows (clockwise).
3.Pull the piece of cloth to one side and cut the threads taking them to the rear side
of the sewing machine.
4.Put the piece of cloth you wish to sew underneath the presser foot ( nº 18)
5.Lower the presser foot with the lever ( nº 8)
6.Choose the stitch you wish to use by turning the stitch dial (nº 10)
7.Finally press down the pedal for the machine to begin to sew.
-Please check that the needles are not bent. To do this pick up the needle and
place the same on a flat surface with the flat side down. If the distance between the
needle and the flat surface is uniform, this means that the needle is straight and can
be used. If the needle is bent it should not be used.
HOW TO REMOVE THE PRESSER FOOT
-The adjustment screw (nº 5) should be used to remove the presser foot, and lift
up the presser foot as high as possible.
-Turn the screw anti-clockwise to remove the presser foot from the machine and it
will come off. To put it in place put the flat surface facing inwards and turn the screw
(nº5) clockwise to fix down the presser foot.
HOW TO TAKE OUT THE ExTRACTABLE ARM
-This machine is provided with an extractable arm.
By using the arm this makes the sewing of sleeves,
waistbands and trouser-legs easier, and additionally
prevents the cloth from piling up around the needle.
E-27