Working With The Petrol Power Scythe - EINHELL GE-BC 43 AS Manual De Instrucciones Original

8. Working with the petrol power
scythe
Extending the cutting line
Caution! Do not use any kind of metal wire or
metal wire encased in plastic in the line spool.
This may cause serious injuries to the user.
To extend the cutting line, run the engine at full
speed and tap the line spool on the ground. This
will automatically extend the line. The blade on
the safety shield will cut the line to the appropriate
length (Fig. 26).
Important: Remove all grass and weed remnants
at regular intervals to prevent the shaft tube over-
heating. Lawn, grass and weed remnants become
trapped under the safety shield (Fig. 27) and
prevent the shaft tube from receiving adequate
ventilation. Remove the remnants carefully using
a screwdriver or the like.
Diff erent cutting methods
When the equipment is correctly assembled it
will cut weeds and long grass in places which are
diffi cult to access, e.g. along fences, walls and
foundations and also around trees. It can also
be used for „mowing" down vegetation so that a
garden can be better prepared or a certain area
cleared down to the soil.
Please note: Even if it is used carefully, cutting
around foundations, stone or concrete walls, etc.
will result in the line suff ering more than normal
wear.
Trimming/mowing
Swing the trimmer from side to side in a scything
motion. Always keep the line spool parallel to the
ground. Check the site and decide which cutting
height you require. Guide and hold the line spool
at the required height to obtain an even cut (Fig.
28).
Low trimming
Hold the trimmer right in front of you at a slight
angle so that the underside of the line spool is
above the ground and the line strikes the correct
target. Always cut away from yourself. Never draw
the trimmer towards yourself.
Cutting along fences/foundations
Approach wire mesh fences, lath fences, natural
stone walls and foundations slowly so that you
can cut close to them without striking the obstac-
Anl_GE_BC_43_AS_SPK9.indb 26 Anl_GE_BC_43_AS_SPK9.indb 26
GB
le with the line. If, for example, the line strikes
stones, stone walls or foundations, it will wear or
fray.
If the line strikes wire fencing, it will break.
Trimming around trees
When trimming around tree trunks, approach
slowly so that the line does not strike the bark.
Walk around the tree, cutting from left to right. Ap-
proach grass or weeds with the tip of the line and
tilt the line spool forwards slightly. Warning! Take
extreme care during mowing work. When doing
such work keep a distance of 30 meters between
yourself and other people or animals.
Mowing
When mowing, you want to cut all the vegetation
down to the ground. To do this, set the line spool
at an angle of 30° to the right. Place the handle in
the required position. Remember the increased
risk of injury to the user, watchers and animals,
and the danger of damaging property due to ob-
jects (for example stones) being thrown up (Fig.
29).
Warning! Do not use the equipment to remove
objects from footpaths, etc. The equipment is a
powerful tool and can throw small stones and
other objects a distance of 15 meters or more,
causing injuries and damage to cars, houses and
windows.
Sawing
The equipment is not suitable for sawing.
Jamming
If the cutting blade jams as a result of attempting
to cut vegetation that is too dense, switch off the
engine immediately. Remove the grass and scrub
from the equipment before you restart it.
Preventing recoil
When you work with the blade, there is a risk of
recoil if it strikes solid objects such as tree trunks,
branches, tree stumps, stones or the like. This will
throw the equipment backwards in the direction
opposite to the rotation of the tool. This can cause
you to lose control of the equipment. Do not use
the blade near fences, metal posts, boundary
stones or foundations. For cutting dense stalks,
position the blade as shown in Fig. 30 to prevent
recoil.
- 26 -
29.05.2019 08:16:41 29.05.2019 08:16:41