Refrigerator Use; Ensuring Proper Air Circulation; Using The Controls - Sears Kenmore ELITE 10654789801 Manual De Uso Y Cuidado

• You may hear the evaporator fan motor circulating air through
the refrigerator and freezer compartments. The fan speed
may increase as you open the doors or add warm food.
• Rattling noises may come from the flow of refrigerant, the
water line, or items stored on top of the refrigerator.
• Water dripping on the defrost heater during a defrost cycle
may cause a sizzling sound.
• As each cycle ends, you may hear a gurgling sound due to
the refrigerant flowing in your refrigerator.
• Contraction and expansion of the inside walls may cause a
popping noise.
• You may hear air being forced over the condenser by the
condenser fan.
You may hear water running into the drain pan during the
defrost cycle.
REFRIGERATOR USE
In order to ensure proper temperatures, you need to permit air to
flow between the two sections. Cold air enters the bottom of the
freezer section and moves up. It then enters the refrigerator
section through the top vent. On Style 2 models, this air is also
evenly distributed throughout the refrigerator compartment
through six vents on the back wall. Air then returns to the freezer
as shown.
Style 1
f
m
Y
Style 2
Do not block any of these vents with food such as soda, cereal,
bread, etc. If the vents are blocked, airflow will be obstructed and
temperature and moisture problems may occur.
IMPORTANT: Because air circulates between both sections, any
odors formed in one section will transfer to the other. You must
thoroughly clean both sections to eliminate odors. To avoid odor
transfer and drying out of food, wrap or cover foods tightly.
Usn9 t se Co st c÷s
Temperature Control Adjustment and Cooling On/Off
The refrigerator and freezer control buttons are located on the
dispenser panel.
Temp
]Aecder IceI
smartsense
o.
off unlocked
Light I Lock ]Filter Status I
OFOC
Units
IMPORTANT: To avoid unintentionally changing other
settings, be sure to press both buttons at exactly the same
time.
For your convenience, your refrigerator and freezer controls are
preset at the factory. When you first install your refrigerator, make
sure that the controls are still set to the "mid-settings."
To view set points, press the TEMP button on your dispenser
panel. The factory recommended set points are 0°F (-18°C) for
the freezer and 37°F (3°C) for the refrigerator.
IMPORTANT:
• Wait 24 hours before you put food into the refrigerator. If you
add food before the refrigerator has cooled completely, your
food may spoil.
NOTE: Adjusting the set points to a higher (colder) than
recommended setting will not cool the compartments any
faster.
• If the temperature is too warm or too cold in the refrigerator or
freezer, first check the air vents to be sure they are not
blocked before adjusting the controls.
• The preset settings should be correct for normal household
usage. The controls are set correctly when milk or juice is as
cold as you like and when ice cream is firm.
• Wait at least 24 hours between adjustments. Recheck the
temperatures before other adjustments are made.
• The display screen on the dispenser control panel has a
backlight, which will turn off automatically when the control
buttons have not been used for 30 seconds or more. When
the backlight is off, the first press of a control button will only
reactivate the backlight, without changing any settings.
Within 30 seconds after the backlight has been reactivated,
additional presses of control buttons will change the
applicable settings.
Adjusting the Controls
To adjust the set points, press and hold the TEMP button for
3 seconds. When adjust mode is activated, set points and
adjusting information will appear on the display screen.
RECOMMENDED(OF)
FREEZER REFRIGERATOR (JF) RECOMMENDED
n°F 3q°F
!,J
OFOC
v I ^ I u°its
To turn cooling off, press and hold the FILTER and UNITS buttons
at the same time for 3 seconds. Press and hold FILTER and
UNITS again to turn cooling on. Your refrigerator and freezer will
not cool when cooling is off.
NOTE: To view Celsius temperatures, press the UNITS button
when adjust mode is activated. To return the display setting to
Fahrenheit, press UNITS again.
11