Selection Of Audioaodeo - Aiwa AV-DV95 Manual De Instrucciones

SELECTION OF AUDIOMDEO
SOURCE
FUNCTION Function indicators
DOWN:UP
I
MULTi JOG
EN+ER
DIGITAUANALOG/BAND
1 Select the program source.
Turn the FUNCTION selector or press the TAPE MONITOR
button. The selected function indicator lights in red.
I ComDact disc I CD
I
I Television, etc. I AUX
I
Video I VIDEO l/DVD/MD.
1
I
I VIDEO 2/LDiTv, VIDEO 3
I
I
LD or Cable TV I VIDEO 2/LD/TV
I MD or DVD I VIDEO l/DVD/MD
I
The function to be selected (except PHONO) depends on the
equipment connected to the input terminals on the rear panel
of the unit.
To select with the remote control
Press the TAPE MONITOR button or the FUNCTION button
repeatedly.
m
When using a turntable with a built-in equalizer amplifier, set
the switch of the equalizer amplifier to off. See the instructions
of the turntable for further information.
2 Start the selected program
source.
3 Adjust the sound,
About the video source to
the
monitor or TV
Selected video source
V1:VIDEO 1,V2:VIDE02,V3:VIDE03
The selected video source is indicated on the display and the
video signal through the MONITOR VIDEO OUT jack is output
on the TV.
To select the video source
1 Trun the FUNCTION to select PHONO, CD or AUX,
2 Press the ENTER button to display VIDEO 1.
3 Turn the MULTI JOG to select VIDEO 2 or VIDEO 3.
To change a displayed
name for the VIDEO 1
and VIDEO 2
When the VIDEO 1 function is selected, VIDEO 1 is displayed
initially. It can be changed to DVD or MD.
Press the DIGITAUANALOG/BAND button while pressing the
ENTER button.
The displayed name for the VIDEO 2 function can be changed
to VIDEO 2, LD or TV; while the VIDEO 2 function is selected,
press the DIGITAL/ANALOG/BAND button while pressing the
ENTER button.
To select the "ANALOG" or "DIGITAL" (Dolby
Digital or
DTS surround) mode of the CD, VIDEO
1, VIDEO 2 or VIDEO 3 function
Press the DIGITAIJANALOG/BAND button when the CD, VIDEO
1, VIDEO 2 or VIDEO 3 is selected. The selected mode
"ANALOG" or "DIGITAL' appears on the display.
In the DIGITAL mode: Equipment connected to the OPTICAL
DIGITAL IN terminal is selected as a source for the CD, VIDEO
1 or VIDEO 3 function, and one connected to the COAXIAL
DIGITAL IN terminal for the VIDEO 2 function. The DIGITAL
indicator lights in red.
In the ANALOG mode: Equipment connected to the CD, VIDEO
l/DVD/MD IN or VIDEO 3 terminals is selected as a source for
the CD, VIDEO 1 or VIDEO 3 function, and one connected to the
VIDEO 2/LDiTV terminals for the VIDEO 2 function.
The "DIGITAL' mode changes to the "ANALOG," when pressing
the TAPE MONITOR button.
When the "OVER LEVEL" indicator lights up
The unit is equipped with the OVER LEVEL indicator. When input
analog signals from the connected equipment are too high to
accept, the indicator lights on the right side of the display. In this
case, adjust the input level as mentioned below so that the
indicator disappears.
To adjust the sound level of the connected source
The input sensitivity level of each function can be adjusted
(except the TUNER, CD(DIGITAL), VIDEO 1 (DIGITAL), VIDEO
2 (DIGITAL) and VIDEO 3 (DIGITAL) functions).
When the sound level of the connected source is higher or lower
than that of the TUNER, adjust it as follows.
1 Select the function to be adjusted.
Turn the FUNCTION or press the TAPE MONITOR button
and play the source.
2 Press the UP or
DOWN button repeatedly.
CEmBmmmcmmm
! :
GEmmElmzzl massiamIim , ,
.... ... ...- ,,.. . ; , ,
.:
;. :..%:...:;...: ;
.,.. :... .... .... :...:
U?5iimimi
Adjust the level so that the "OVER LEVEL' indicator does not
light on the display.
The level can be adjusted between -6dB (MIN) and +8dB
(MAX) in 2dB steps. Adjust the level so that the sound is
output at the same level as the TUNER.
The input sensitivity level of the TAPE MONITOR can be
adjusted to OdB or -6dB.
11
ENGUSH