Two-Man Operation; Using Attachments; Ns-Csp 250X50 Planing Attachment; Rs-Csp 160X80 Curve-Cutting Attachment - Protool CSP 132 E Manual De Instrucciones

8.2 Two-Man Operation

The machine has several handholds to allow it
to be used by one or two operators, depending
on the confi guration.
Illustration 4a is for one-man operation.
Illustration 4b is for two-man operation.

9 Using Attachments

You can extend the use of your circular saw by
using the NS-CSP 250x50 planing attachment
and the RS-CSP 160x80 curve-cutting attach-
ment available from the Protool range.
WARNING
Risk of electric injury.
►
Before any manipulation with the tool make
sure to unplug the mains socket outlet.
9.1 NS-CSP 250x50 Planing
Attachment
Using the planing attachment (item no. 624
337), you can mill grooves and rabbets to a
max. depth of 80 mm and a width of 50 mm
(see diagrams below).
max 80 mm
max 36 mm
Set the saw to minimum cutting depth.
Remove the saw blade [3-3] by following the
instructions in Section 7.7 (Replacing the saw
blade).
Unscrew the following components:
Plate [5-1] covering the blade guard
Guard [5-2] covering the pendulum mount
Dust exhaustion connection [5-3]
Riving knife [5-4]
Ensure the planing head [6-3] is clean and fi t-
ted according to the illustration and screw it
tight. Ensure that the mounting fl ange [6-1]
and the clamping fl ange [6-2] are in the cor-
rect position. The holes in the planing head
[6-3] must fi t onto the follow-up pins on the
mounting fl ange [6-1]. Insert the pin [6-4]
into the hole on the planing head to secure it.
50 mm
80 mm
Screw the cover guard [6-5] onto the pendu-
lum mount [6-6].
Screw the cover guard [6-7] onto the blade
guard [6-8].
Select the depth to be milled as described in
Section 7.2 (Cutting Depth Adjustment).
9.2 RS-CSP 160x80 Curve-Cutting
Attachment
Using the curve-cutting attachment (item no.
624 339), you can sink grooves, mill and cut
curves as illustrated below. For this purpose,
the curve-cutting attachment swivels by up to
45°.
80 mm
max 56 mm
Set the saw to the minimal cutting depth.
Remove the saw blade [3-3] by following the
instructions in Section 7.7 (Replacing the saw
blade).
Unscrew the following components:
Plate [5-1] covering the blade guard
Guard [5-2] covering the pendulum mount
Dust exhaustion connection [5-3]
Riving knife [5-4]
Ensure the curve-cutting head [7-3] is clean
and fi tted according to the illustration and
screw it tight. Ensure that the mounting fl ange
[7-1] and the clamping fl ange [7-2] are in the
correct position. The holes in the curve-cutting
head [7-3] must fi t onto the follow-up pins on
the mounting fl ange [7-1]. Insert the pin [7-4]
into the hole on the curve-cutting head to se-
cure it.
Screw the cover guard [7-5] onto the pendu-
lum mount [7-6].
Screw the cover guard [7-7] onto the blade
guard [7-8].
Select the depth to be milled as described in
Section 7.2 (Cutting Depth Adjustment) and
the angle to be milled as described in Section
7.3 (Cutting Angle Adjustment).
You can check the curve depth against the
angle to be milled on the table on the blade
guard.
80 mm
45°
max 50 mm
23