Maintenance - Tunturi T10 Manual Del Usuario

elevation program will
PROGRAM 6 – PROGRAM 7:
change automatically during the exercise).
Press the SPEED + –button to set up your desired
a.
program.
The time window will glitter. Use the ELEVATION
b.
+ – or SPEED+ –buttons to set up the desired
exercise time.
Press the Enter to confirm your setting value.
c.
Distant window will glitter. Use the ELEVATION
d.
+ – or SPEED+ – buttons to set up the desired
distance to do the exercise.
Press the Enter to confirm your setting value.
e.
Kcal window will glitter. Use the ELEVATION +
f.
– or SPEED+ – buttons to set up the desired calories
to be consumed.
Press the Enter to confirm your setting value.
g.
Press Start to begin exercise.
h.
NOTE:
If you would not like to select any special target to
1.
reach, just press Start to do the exercise.
If you would like to skip the target setting, press
2.
the enter key to next setting value and this function
will count up.
If you set up more than one target, once reach
3.
the first target, Press Start again and this value will
continue to count down until reach your next target.
USER1 – 2
Press SPEED + - or ELEVATION + - button to
a.
enter your desired User setting program.
The time window will glitter. Use the ELEVATION
b.
+ – or SPEED+ – buttons to set up the desired
exercise time.
Press the Enter to confirm your setting value.
c.
Distant window will glitter. Use the ELEVATION
d.
+ – or SPEED+ – buttons to set up the desired
distance to do the exercise.
Press the Enter to confirm your setting value.
e.
Kcal window will glitter. Use the ELEVATION +
f.
– or SPEED+ – buttons to set up the desired calories
to be consumed.
Press the Enter to confirm your setting value.
g.
The SPEED and ELEVATION windows will glitter.
h.
Press SPEED+ or –to set up desire speed and/or Press
ELEVATION + or – to set up desired level of incline.
Press Enter to confirm the first column.
i.
Follow h points to finish the user setting profile.
j.
Total profile setting is 20 times. (20 columns)
Press Start to begin exercise.
k.
NOTE:
If you would not like to select any special target to
1.
reach, just press Start to do the exercise.
If you would like to skip the target setting, press
2.
the enter key to next setting value and this function
will count up.
If you set up more than one target, once reach
3.
the first target, Press Start again and this value will
continue to count down until reach your next target.
ENGINEERING MODE
during the power ON position, first hold the
1.
SELECT button then press the ENTER button
O W N E R ' S M A N U A L • T 1 0
together to enter the Engineering Mode
Speed window shows software version, Time
2.
window shows year, Distance window shows date.
Press ENTER button window shows LDU version.
3.
It is software version.
Press ENTER button window shows ISP version. It
4.
is software version.
Press ENTER button enter KM/MILE switch mode,
5.
1 means KM, 0 means MILE
Press SPEED + - or ELEVATION + - to select KM or
MILE.
Press ENTER button window shows total distance.
6.
Press ENTER button window shows total hour.
7.
Press ENTER button goes back to ON position.
8.

MAINTENANCE

The equipment is safe to use only when periodically
maintained and inspected for faults and wear.
Do not attempt any servicing or adjustment
CAUTION!
other than those described in this manual. Any other
servicing must be performed by an authorized service
representative. Check the tightness of all fixing
screws once a year. Do not overtighten.
LUBRICATING THE RUNNING DECK
Lubrication is the most important service activity
for the treadmill. This is absolutely essential, if the
friction of the running deck increases noticeably or
the motor begins to heat up; increased friction is
indicated by jerky movement of the belt. Insufficient
lubrication will cause the belt, running deck and
motor to wear out and break. The need for re-
lubrication depends to a great extent on the running
styles and weight of the user: heavy user weight and
slow speed put particular strain on the device and
therefore demand greater lubrication. The running
deck requires periodic lubrication. With average
usage (30 minute workout session 3 times a week),
lubricate every four to six months. You may adjust
the timing of the lubrication based on the intensity of
the treadmill use level. To check the lubrication level,
simply lift the running belt, and put your hand as far
into the center of the belt as you can reach. If your
hand shows signs of lubricant (some wetness), then it
does not need additional lubrication. If the board feels
dry and there is very little evidence of lubricant on
your hand, then additional lubrication should be added
as instructed:
Stop running belt so belt seam is located on the top
1.
and in the center of the deck.
Insert nozzle into spray head of lubricant can.
2.
Lift running belt.
3.
Position nozzle between the belt and the board
4.
approximately 200 mm (8") from the front of the
treadmill.
Apply T-Lube from the front to the rear of the
5.
treadmill on each side of the treadmill. Try to reach
the spray as far into the center of the running deck as
possible.
The treadmill is instantly ready for use.
6.
G B
7