Maintenance; General; Cleaning; Draining The Reservoir - Hatco FLAV-R-SAVOR FSD Serie Manual De Instalación Y Funcionamiento

MAINTENANCE

GENERAL

The Hatco Flav-R-Savor ®
designed for maximum durability and performance, with
minimum maintenance.
WARNING
To avoid any injury, turn the power switch OFF, unplug the
unit from the power source and allow to cool before
performing any maintenance.

CLEANING

WARNING
To avoid electrical shock or personal injury, do not steam
clean or use excessive water on the unit.
WARNING
Unit is not waterproof. DO NOT submerge in water. Do not
operate if it has been submerged in water.
To preserve the bright finish of the Flav-R-Savor cabinet, it is
recommended that the exterior and interior surfaces be wiped
daily with a damp cloth. Food pans should be removed and
washed. Air distribution duct is removable for cleaning.
Stubborn stains may be removed with a good stainless steel
cleaner or a non-abrasive cleaner. Hard to reach areas should
be cleaned with a small brush and mild soap.
CAUTION
Use only non-abrasive cleaners. Abrasive cleaners could
scratch the finish of your unit marring its appearance and
making it susceptible to soil accumulation.
Clean the glass sides using a common glass cleaner. For hard-
to-clean stains, removal of the glass is suggested.
Removing Glass
1. Lift the glass to be cleaned from the bottom of the cabinet.
2. Pull the lower edge away from the cabinet.
3. Carefully lower the glass until the top clears the cabinet.
Installing Glass
1. Position the glass with the top edge under the cabinet lip
and raise the glass until it clears the bottom channel of the
cabinet.
2. Move the bottom of the glass towards the cabinet until the
glass rests against the cabinet frame.
3. Carefully lower the glass until it rests in the bottom channel
of the cabinet.
Removing Rotating Rack
(Models FSD-1, FSDT-1, FSD-2, FSDT-2)
1. Open the front access door.
2. Remove the two cotter pins from the rotating rack coupling
located at the top of the rack inside the cabinet.
See 9 .
3. Lower the connecting coupling until it is free of the motor
shaft and remove the rack from the cabinet.
Form No. FSDCEM-0805
Holding & Display Cabinets are
Installing Rotating Rack
(Models FSD-1, FSDT-1, FSD-2, FSDT-2)
1. Insert the rack into the cabinet through the access door and
place the rack bottom point in the dimple located at the
center of the cabinet floor.
2. Slide the rack coupling up onto the motor shaft and align
the coupling holes.
3. Insert the two cotter pins through the coupling and shaft.
Units with a motorized rotating style display use safety
door switches that turn the rotating rack off when a door is
opened. If the rack rotates when a door is opened, unplug
the unit and contact your Authorized Service Agent for
service.

DRAINING THE RESERVOIR

To avoid any injury, turn the power OFF to the unit and
allow to cool before draining.
It is recommended that the Flav-R-Savor water reservoir be
drained prior to moving the cabinet and after removing lime or
mineral deposits from the water reservoir.
NOTE: The drain hose assembly is located in the corner of the
cabinet inside the rear door.
NOTE: Position a container to hold the water while draining.
NOTE: To ease installation, moisten the inside of the drain hose
end with water before installing.
1. Insert the drain hose fitting into the water outlet, located on
the ceiling of the cabinet. Once the fitting is installed, water
will begin to drain from the hose. See 10 .
2. Once the unit has finished draining, the drain tube
assembly can be removed by pressing the release tab and
gently pulling the fitting out.
3. Place the drain tube back into the holding clips inside the
rear door.

DISPLAY LIGHT BULB REPLACEMENT

Only light bulbs which meet or exceed N.S.F. standards,
specifically designed for food holding areas must be used.
Breakage of light bulbs not specially coated or covered
could result in personal injury and/or food contamination.
Be sure the protective lens cover for the light bulbs are
installed. Breakage of a bulb not properly covered could
result in personal injury and/or food contamination.
The unit is equipped with two 120 Volt fluorescent light tubes
which illuminate the warming area. These tubes have a special
lens cover to guard against injury and food contamination in the
event of breakage. When replacing a fluorescent light, use
Hatco part #02.30.074.00.
To replace a fluorescent light, disconnect the power supply and
wait until the unit has cooled. Remove the protective lens cover
from the fixture and then carefully twist the fluorescent tube and
gently pull to remove it from the sockets.
14
WARNING
WARNING
WARNING
WARNING