Product Familiarisation; Intended Use; Unpacking Your Tool; Before Use - Triton TMUTL Instrucciones De Uso

b) Keep your workplace clean. Dusts created from different materials including woods and
metals can be highly flammable. Dust from light alloys including magnesium can burn or
explode easily.
c) DO NOT treat the work surface with fluids containing solvents. If such fluids become
warm from scraping, toxic vapours may be produced, or surfaces may catch fire.
WARNING: NEVER fit any blade or accessory with a maximum speed lower than the no
load speed of the power tool.
d) ONLY change accessories and blades or perform maintenance with the tool
disconnected from its power supply, either mains connection or battery. If the tool
features a captive battery in a charged state take extra care not to switch it on accidentally
when changing accessories or blades.
e) ALWAYS use accessories or blades that are approved by the manufacturer or meet
the specification of your power tool, this includes being compatible in size and speed.
DO NOT try to cut material thicker than the capacity stated in the specification.
f) ONLY use an adapter for using different accessories or blades if the adapter is
specifically designed and approved by the manufacturer of your power tool.
g) DO NOT modify accessories or blades so they work with power tools they were not
intended to work with or for uses that they were never designed for.
h) DO NOT use accessories or blades that are damaged, bent, chipped, cracked, heavily
corroded or excessively worn. Such accessories can break apart in use causing injury to
the operator. ALWAYS inspect accessories or blades before use and discard immediately if
not in good condition. NEVER use blades that are worn to a dull edge. ALWAYS use sharp
blades.
i) ALWAYS ensure all accessories or blades are securely attached to the tool before use
and the securing tool is removed prior to use.
j) DO NOT attempt to free a jammed blade or accessory until the power tool has been
disconnected from power.
k) Inspect the workpiece before use to make sure it is in the correct condition for the
fitted accessory or blade. Remove all nails, staples and other embedded objects prior to
starting work.
l) Any freely movable workpieces should be secured with a clamp or vice before
starting work.
m) ALWAYS ensure that the lighting is adequate in the work area. Never remove your
safety goggles or glasses to improve your view instead increase the level of lighting or
move the lighting so it specifically illuminates the work area correctly.
n) DO NOT operate the power tool near flammable materials. Be especially careful when
cutting wood and metal. Sparks from metal cutting are a common cause of wood dust fires.
o) Battery chargers are for indoors use only. Ensure that the power supply and charger are
protected against moisture at all times.
p) NEVER start the power tool while the blade or accessory is in contact with the
workpiece, and always allow the power tool to reach its full speed before making
contact with the workpiece. Use the variable speed control of the tool (if fitted) to start the
tool at the correct speed for the accessory or blade fitted.
q) DO NOT exert additional pressure on the body of the tool: allow the blade or
accessory to do the work. By not exerting additional pressure you maintain a safer
stronger grip on the power tool when it breaks through the material, as well as
reducing wear on the power tool which will extend the power tool's service life.
Additional pressure may also bend or twist the accessory or blade which may cause
it to break and cause injury. If the power tool allows for being held with one or two
hands hold with two hands whenever possible. ALWAYS exercise caution when
handling this power tool.
r) Sawing, cutting and abrasive actions create heat. This may affect the workpiece and
power tool. ALWAYS monitor the heat level and in the event of excessive heat switch off the
power tool and allow to cool before restarting work. Some power tools depending on design
may be more quickly and effectively cooled by running at high speed without load.
s) The power tool will draw in dust through the vents on its body. Excessive accumulation
of powdered metal may cause an electrical hazard and destroy the tool. ALWAYS ensure the
environment dust level is safe for the tool and ensure the vents are not blocked.
t) For mains-operated power tools, ensure the cable of the power tool is ALWAYS kept
behind the tool and never close to where the accessory or blade is operating.
u) DO NOT reach under the workpiece, rest the workpiece on your body, or hold the
workpiece while working on it, as contact with the blade or accessory protruding
from the workpiece can result in serious injury.
v) Anti-vibration gloves should be worn when operating power tools that produce large
amount of vibration, especially during long-term use.
w) For power tools with a rotating mechanism and accessories ensure the operator is
not wearing clothes or gloves with frayed threads, cords etc. that could be entangled
in the rotating mechanism dragging the operator's hand into the rotating accessory
causing injury. ALWAYS wear tight fitting work clothes, safety shoes. Remove jewellery
and secure long hair. NEVER wear fabric-based gloves that can produce strands of material
when operating this type of power tool.
x) DO NOT allow sanding sheets to wear away on the sanding pad. This will damage the
surface of the pad requiring replacement and may cause parts of the sanding sheet to fly
off the pad, causing operator injury.
y) DO NOT touch the moving sanding sheet.
z) Wire brush bristles are thrown by the brush even during ordinary operation. DO NOT
overstress the wires by applying excessive load to the brush. The wire bristles can easily
penetrate light clothing and skin.
8
WARNING
Some dust created by power sanding, sawing, grinding, drilling and other construction
activities contains chemicals known to the State of California to cause cancer, birth
defects or other reproductive harm. Some examples of these chemicals are:
• Lead from lead-based paints
• Crystalline silica from bricks and cement and other masonry products, and
• Arsenic and chromium from chemically-treated lumber
Your risk from these exposures varies, depending on how often you do this type of work.
To reduce your exposure to these chemicals: work in a well-ventilated area, and work
with approved safety equipment, such as those dust masks that are specially designed
to filter out microscopic particles.

Product Familiarisation

1. Cutting/Sanding Accessory
2. Dust Extraction Collar
3. Dust Extraction Port
4. Keyless Change Lever
5. ON/OFF Switch
6. Grip
7. Variable Speed Dial
8. Motor Vents
9. Auxiliary Handle Hole
10. Auxiliary Handle
11. Work Light
12. Flange
13. Dust Collar Threaded Holes
14. Locking Knob
Included accessories (not shown)
• 1 x Round carbide blade
• 1 x Rasp sanding pad
• 1 x Hook & loop sanding pad
• 25 x Sandpapers (P60, P80, P120, P180, & P240)
• 2 x Scraper blades
• 2 x Saw blades
• 1 x Accessory holder

Intended Use

Oscillating multi-tool with quick keyless tool-change mechanism, designed for cutting and
abrasive tasks by fast oscillation of a blade, file or sanding pad.

Unpacking Your Tool

• Carefully unpack and inspect your tool. Fully familiarise yourself with all its features and
functions
• Ensure that all parts of the tool are present and in good condition. If any parts are missing
or damaged, have such parts replaced before attempting to use this tool

Before Use

WARNING: Always ensure that the tool is switched OFF and unplugged from the power
supply before fitting or removing the Dust Extraction Collar or accessories.
WARNING: Always wear suitable gloves when handling blades or other sharp accessories.
WARNING: Accessories and tool may become hot during use. Always allow to cool before
removing or changing accessories.
Fitting the Dust Extraction Collar
Note: This Keyless Oscillating Multi-Tool is designed to be connected to a household vacuum
cleaner hose or workshop dust extraction system. This is the preferred and most effective
method of dust extraction.
WARNING: ALWAYS connect the Keyless Multi-Tool to a suitable vacuum cleaner or
workshop dust extraction system if the sanding dust contains harmful substances, such
as particles from old paint, varnish, surface coatings, etc. ALWAYS dispose of harmful dust
according to laws and regulations.
1. Ensure the tab on the Dust Extraction Collar (2) aligns with the notch on the head of the
multi-tool, with the Dust Extraction Port (3) facing up (Fig. I)
2. With the tab and notch aligned, place the Dust Extraction Collar over the Flange (12) and
onto the head of the multi-tool (Fig. I)
3. Turn the dust post on the Dust Extraction Collar to the desired side, left or right, of the multi-
tool (Fig. II)
4. Locate one of the fixing holes on the Dust Extraction Collar and align it with one of the Dust
Collar Threaded Holes (13) (Fig. II)