Enjoying Surround Sound - Yamaha YSP-900 Manual De Instrucciones

Ocultar thumbs Ver también para YSP-900:

Manual de instrucciones (272 páginas)

Tabla de contenido

Continued

Carry out the AUTO SETUP (IntelliBeam) procedure to adjust the settings that

from the front

best match your listening environment.

This unit employs the YAMAHA IntelliBeam technology with the aid of the supplied optimizer microphone, allowing you to achieve highly accurate sound adjustments

that best match your listening environment. Be advised that it is normal for loud test tones to be output during the AUTO SETUP procedure. Make sure that there are

no children around in the listening room while the AUTO SETUP procedure is in progress.

Press STANDBY/ON on

STANDBY/ON

the remote control.

The power of this unit turns on.

STB

VCR

If a subwoofer with adjustable volume and

crossover/high cut frequency controls is

VOLUME

connected to this unit, set the volume

between 10 and 12 o'clock as viewed on

a conventional clockface and set the

crossover/high cut frequency to the

maximum.

MIN

MAX

Subwoofer

Turn on the power of your TV.

Select the appropriate video input

on your TV.

Set the operation mode selector to YSP.

CH LEVEL

TV/AV

ENTER

YSP

TEST

RETURN

Press and hold AUTO SETUP for more than 2

seconds.

The menu screen appears on the TV.

If the menu screen does not appear, check the video pin cable (connection

3 in the diagram on the front page) is connected properly and then press

YSP followed by MENU.

AUTO SETUP

STB

VCR

DVD

AUX

PREPARATION & CHECK

INPUT1

INPUT2

MACRO

Please connect the MIC.

Please place the MIC at least

1.8m/6ft away from the YSP

AUTO

VOL MODE

SETUP INPUTMODE

SLEEP

unit. The MIC should be set

at ear level when seated.

Measurement takes about 3min.

5BEAM

ST+3BEAM

3BEAM

After [ENTER] is pressed,

please leave the room.

[ENTER]:Start [RETURN]:Cancel

Check the following points.

POWER

・Is the optimizer microphone firmly connected to this unit?

・Is the optimizer microphone placed in a proper loacation?

・Are there any large obstacles in between the optimizer microphone and the

walls in your listening room?

DVD

AUX

・The AUTO SETUP procedure starts in 10 seconds after pressing ENTER

on step 7. To achieve the best results possible, evacuate yourself for your

CROSSOVER/

listening room until the AUTO SETUP procedure is completed.

HIGH CUT

・To cancel the AUTO SETUP procedure after it is started, press RETURN.

・The AUTO SETUP procedure takes about 3 minutes.

MIN

MAX

Press ENTER to start the AUTO SETUP procedure.

The following screen appears on the TV and the AUTO SETUP procedure

starts in 10 seconds.

CH LEVEL

TV/AV

ENTER

YSP

RETURN

TEST

The setup screen automatically changes during the AUTO SETUP

procedure.

If any error occurs, the corresponding error message appears on the screen.

In this case, see "Error messages for AUTO SETUP" on page 33 in the

Owner's Manual and then follow the instructions. To start the AUTO SETUP

procedure once again, press RETURN and then carry out the procedure from

step 5.

When the AUTO SETUP procedure is complete, the following screen

appears on the TV.

SHOW RESULT

MEASUREMENT COMPLETE

BEAM MODE :5 BEAM

SUBWOOFER:NOT APPLICABLE

[ENTER]:Save set-up.

[RETURN]:Do not save set-up.

Press ENTER.

The result is confirmed and the following screen appears on the TV for 2

seconds and then the menu screen disappears from the TV.

The new settings are automatically saved in the system memory.

Disconnect the optimizer microphone and keep it in a safe place.

CH LEVEL

TV/AV

ENTER

YSP

TEST

RETURN

Enjoy TV or DVD audio in surround sound.

For instructions on your TV or DVD player, refer to the owner's manual supplied with each component.

Before carrying out the procedure below, set the volume of this unit to 30. If necessary, adjust the volume level in

step 4.

Enjoying TV in surround sound

Select the TV channel using

the remote control supplied

with your TV.

Set the operation mode selector to YSP .

AUTO SETUP START

Will begin in 10sec

Press TV on the remote

Please leave the room

**--------

control of this unit.

[RETURN]:Cancel

This unit switches to the TV playback mode.

If you hear sound output from your TV speakers, turn down the volume level

This is an example of the result screen.

until you cannot hear any sound.

The result may differ depending on the

environment.

Use the remote control supplied with your TV.

Press VOLUME +/– on the remote control to adjust

the volume level of this unit.

Press one of the beam mode buttons on the

remote control to select the desired beam mode.

Select one of the three beam modes that best matches the current input source of

this unit.

AUTO SETUP COMPLETE

For further information on the beam modes, see page 40 in the Owner's Manual.

Please remove the MIC from

the YSP and the listening

position.

To fine-tune the listening environment parameters manually or make advanced settings for

speaker positions, sound beams, etc., see "MANUAL SETUP" on page 57 in the Owner's Manual.