Warranty; Installation - Flotec FP0S4100X Serie Manual Del Usuario

Installation

DESCRIPTION
These submersible pumps are designed for use in water-
fall/ fountain applications or as a utility pump. The units
are equipped with a 3-prong grounding-type power cord.
Ball bearings on motor shafts never need lubrication.
Automatic reset thermal protection.
Pump water only with this pump.
SPECIFICATIONS
Power supply required..................................115V, 60 HZ.
Motor duty .......................................................continuous
Liquid Temp. Range .....................32°F to 100°F (0°-38°C)
Individual Branch Circuit
Requirement (minimum) ......................................15 Amps
Discharge Fittings:
...........................1/2", 3/4", and 1" Barbed Hose Adapter
.................................................1-1/4" x 1" FNPT Reducer
........................................................Garden Hose Adapter
NOTICE: Not designed for applications involving salt
water or brine! Use with salt water or brine will void

warranty.

ELECTRICAL SPECIFICATIONS
Motor
Motor Full Load
Model H.P. Amps
FP0S1200X 1/6 1.5
FP0S2300X 3/10 2.6
FP0S3000X 4/10 3.0
FP0S4100X 1/2 7.2
INSTALLATION
See Figure 1 for typical installation connections to pump
(NOTE: Fountain accessories not included with pump).
PERFORMANCE
Motor
Model HP (.3 M)
FP0S1200X 1/6 1,200 (4,542) 1,000 (3,785)
FP0S2300X 3/10 2,300 (8,858) 1,975 (7,476) 1,425 (5,394)
FP0S3000X 4/10 3,000 (11,356) 2,500 (9,464) 1,900 (7,192) 1,320 (4,997)
FP0S4100X 1/2 4,100 (15,520) 3,600 (13,627) 3,000 (11,356) 2,400 (9,085) 1,625 (6,151)
For parts or assistance, call Flotec Customer Service at
Minimum Pumps
Circuit Down
Req. (Amps) To
15 7/16" (11mm)
15 7/16" (11mm)
15 7/16" (11mm)
15 1-3/8" (35mm)
GPH (LPH) AT TOTAL FEET (M)
1 5
(1.5 M)
675 (2,555)
GFCI
outlet
Power
cord
Landscaping
rocks
Figure 1: Typical Garden Pond and Waterfall
Installation.
1. Install the pump on a hard level surface. Make sure
that the pump cannot pick up rocks, mud and debris,
etc. If neccesary, put a block under the pump to raise
it slightly. If used with a fountain jet, position the
pump so that the fountain jet is above the surface of
the water.
2. Protect the power cord from damage. Uncovered
cords should be routinely inspected for damage or
deterioration. DO NOT operate the pump if the cord
is damaged.
3. If used in a garden pond, adjust the diverter valve to
control the fountain spray height and flow over the
waterfall. Do not restrict pump suction to adjust
flows. Restrictng the suction will starve the pump for
water and can damage the pump.
4. If the pump is connected to a pond filter, adjust the
diverter valve to provide adequate flow to the filter.
Refer to the filter instruction manual to determine
flow requirements of filter.
10 15
(3 M) (4.6 M)
400 (1,514)
850 (3,218)
Use foliage to cover
tubing to waterfall
Diverter
valve
Raise the pump
off of the bottom
of the pond
20 25
(6.1 M) (7.6 M)
– –
300 (1,136) –
750 (2,839) –
920 (3,483)
1-800-365-6832
4
Plastic
tubing
to waterfall
3388 0399
No Flow
At Height
Shown Below
20' (6.1 M)
22' (6.7 M)
25' (7.6 M)
30' (9.1 M)