30%
Duty cycle
Protection rating
Insulation class
Working temperature
Max weight of gate
Rack module
Maximum speed
Weight
4
INSTALLATION
4.1 PRELIMINARY CHECKS
For correct operation of the automation system, make sure:
• All the accessories are suitably sized and properly maintained.
• During manual operation the gate is not subject to swaying or bending.
• The gate is equipped with mechanical limit stops capable of arresting its closing
and opening movements.
• The sliding gate does not move autonomously, when released in any position.
• There are no points of friction throughout the entire opening or closing travel of the
gate.
4.2 APPLICATION LIMITS
Before installing the operator, make sure its specifications are within the application
limits in the chapter "Product technical specifications". The gate must never exceed
the maximum weight permitted for the chosen operator.
4.3 INSTALLING THE FORT 3500 OPERATOR
4.3.1 INSTALLATION:
• Release the operator as described in heading 4.3.3.
• Secure the 4 anchor bolts as shown in FIG. 1A.
• Embed the anchor bolts in concrete, taking care to route the electrical cables
through the specific hole in the operator baseplate. (FIG. 1A). If installing the
operator on a dry concrete footing, fix it to the ground with 4 suitable plugs (FIG.
1B). Take care to position the operator such that it can mesh correctly with the rack
mounted to the gate.
• Mesh the rack with the pinion leaving a 1 to 2 mm backlash between the teeth.
This backlash must remain constant over the entire length of the rack (FIG. 2).
• Fix (or weld) the rack to the gate (FIG. 3).
• Perform a few manual gate opening and closing cycles to ensure the rack-pinion
mesh has the same backlash over the full travel distance and that there are no
points of abnormal friction that could overload the operator. (FIG. 4).
4.3.2 INSTALLATION OF LIMIT STOPS AND SWITCHES
ELECTRONIC LIMIT SWITCH
• Bring the gate to its open position manually, stopping at a distance of 3 cm from
the mechanical limit stop (FIG. 5).
• Slide the limit switch bracket along the rack until reaching the mid-point of the limit
switch (FIG. 6).
• Keep a distance of between 3 and 8 mm between bracket and limit switch (FIG.
7).
• Fix the bracket to the rack with the dedicated screws (FIG. 8).
• Perform the same operation for the closing limit switch.
• Position the gate centrally (FIG. 9) and restore motorized control as described in
heading 4.4.3.
4.3.3 MANUAL RELEASE
Perform the manual release procedure when the gate is to be opened manually.
Activation of the release system may result in uncontrolled movements of the gate in
the presence of imbalance or mechanical faults.
• Open the front hatch using the supplied key (FIG. 10).
• Undo the nut in line with the drive shaft until almost bringing it to rest against the
circlip (FIG. 11).
• Use a rubber mallet to strike the threaded bar as shown in FIG. 12.
• To re-lock the operator tighten and lock the release nut.
5 PREPARATION FOR ELECTRICAL
CONNECTIONS
WARNING! Connect to the mains using a multicore cable of at least 3x1.5mm2
section and of a type that complies with the regulations in force.
FORT 3500
Insert the wiring through the specific hole on the base of the operator.
Intensive
• Route the wiring into the control board container through the specific cable glands.
IP 24 D
• Connect the power supply wires to the circuit board following the electrical
1(Earthing)
from -20°C to + 50°C
• Connect the ground wire (protection wire)
• The earth conductor must be connected to the specific terminal located alongside
3500 Kg
M 6
• Close the front hatch.
0,17 m/s
70 Kg
6 TESTING
Each part of the automation system, e.g. safety edges, photocells, emergency stop,
etc. must be tested; follow the procedures shown in the instruction manuals supplied
with the devices in question. Perform the following sequence of operations for testing
of FORT 3500:
• Check that all the prescriptions in this manual have been followed scrupulously,
• Using the supplied control or stopping devices (key selector switch, pushbuttons
• Check operation of all the system's safety devices (photocells, safety edges,
7 PRODUCT MAINTENANCE
Maintenance must be carried out at regular intervals by qualified personnel in
compliance with the provisions of statutory legislation and the regulations in force.
FORT 3500 must be serviced at least once every 6 months or after 10.000 operating
cycles since the last service.
• Disconnect the operator from all power supplies.
• Check all the moving parts and renew any worn parts.
• Check all parts of the automation system for signs of deterioration.
8 SPARE PARTS
Spare parts can be purchased by contacting the technical service.
9 DISPOSAL
At the end of its useful life the automation system must be dismantled by qualified
personnel and the materials must be recycled or disposed of in compliance with the
local legislation in force.
10 WARRANTY
Fratelli Comunello SpA provides a warranty for 24 months for the correct functioning
of the actuators from the date of manufacture, provided that the performance
specications indicated in the product instruction manuals are respected. Free of
charge repair and replacement of components that are found to be faulty according
to the indisputable judgment of the company's technical staff shall be guaranteed at
the sole discretion of Fratelli Comunello Spa, and so excluding any claim for damages
made by others. Warranty material shall be returned to Fratelli Comunello S.p.a.
headquarters carriage paid and will then be shipped to the customer carriage unpaid.
The material found to be faulty and returned to Fratelli Comunello S.p.a. shall remain
property of the Seller. Any cost resulting from any work needed to repair the defect
or to replace the material shall be charged to the Buyer. No compensation shall be
allowed for the period of device inactivity. Work under warranty does not prolong the
warranty period. The defect of the product shall be reported by the Buyer within 8
(eight) days from its discovery or from the date of delivery of the goods, under penalty
of invalidation of the warranty. Such claim shall be notied in writing.
Warranty does not cover:
Any product defect or damage that may have been incurred during transport; any
defect or damage arising from any fault and/or from neglect, inadequacy and misuse
of the electrical wiring in the Buyer's property; any defect or damage caused by
any repairs carried out by non authorised personnel or by incorrect use/installation
(with reference to this, system maintenance is recommended every 6 months) or if
not original spare parts are used; any defect caused by chemicals or atmospheric
conditions. The warranty does not cover any cost neither for consumable materials
nor for alleged defects or convenient surveys.
Product Features Fratelli Comunello SpA products are subjected to continue changes
and improvements; their technical features and image may therefore change without
previous notice.
Competent court
Since the contract of sale is conrmed by an Order Conrmation drawn up in Rosà,
any such dispute shall be settled by the laws of Italy and by the court of Vicenza (VI).
connections diagram.
the electronic control board inside the box.
with special attention to the matters set down in chapter 1 "General Prescriptions".
or radio transmitters), perform gate opening, closing and stopping tests and make
sure the gate responds correctly to the various commands.
emergency stop, etc.) one by one.
COMUNELLO ®Copyright 2013 - All right reserved
11