Publicidad
Idiomas disponibles
Idiomas disponibles
For safes with a fingerprint lock
IMPORTANT
For some fingerprint locks
NOTE: Some models with a fingerprint lock are shipped with
a screw in the back of the door (Fig. H). This temporary screw
keeps the handle from turning and locking the safe before you
are ready to use it. Once your safe is delivered, remove this screw
and throw it away (Fig. I). After removing the lock out screw, it
may be required to push the bolt button which, in turn, will throw
the bolts to a locked position while the door is open (Fig. J).
The handle should be all the way UP, in the horizontal
position before attempting to program your safe. Your
finger-print lock is now ready to use. You will find your safes
factory combina tion on the sticker on the front of the
owner's manual.
H
I
J
NOTE: If you are experiencing difficulty with the
operation of the locking mechanism, DO NOT
RETURN THIS PRODUCT TO THE STORE. PLEASE
CONTACT SENTRY GROUP CUSTOMER SERVICE
at 1-800-828-1438 for assistance. Most problems
can be quickly resolved over the telephone.
It is important that you keep this Owner's Manual in a secure
place other than IN your safe; it is your reference for the
safe's Serial Number and Factory Code.
To activate lock
Four alkaline AA batteries, equaling voltage: 6Vdc, (not included)
are required to activate the fingerprint lock.
NOTE: Non-alkaline and rechargeable batteries ARE
NOT RECOMMENDED.
To install batteries:
The battery compartment is located directly beneath the keypad.
Insert a small coin in the slot on the left side of the compartment
cover. Twist the coin to dislodge the cover, then slide it to the
right. Insert four new batteries as indicated, and slide the cover
back in place.
Low battery notice
When the battery power gets low, the message "Batteries Low
Replace Soon" will appear with each activation of the lock until
batteries are replaced.
NOTE: No codes are erased when old batteries are
removed for replacement.
First time use
Open unit first, then test
with door open!
When you have successfully completed the personal code
process described below, the LCD on the screen will prompt the
next steps. The instructions provided here serve as a beginning
guide.
NOTE: The key lock must be in the UNLOCKED position
in order to operate the fingerprint lock.
To unlock, turn the key to the right. Return
key to the locked position when you have closed
the safe door. Remove the key from the lock
and store it in a secure location other than
in the safe.
To enter your personal code
1. Press ENTER .
2. Enter the 5-digit factory code provided on the front
of this manual.
3. Press ENTER .
NOT E: When you have successfully entered the
factory code, the LCD screen will prompt the
next steps.
If you require additional assistance,
contact Sentry Customer Service on line at
www.sentrysafe.com, or call: 1-800-828-1438,
8:00am – 6:00pm E.S.T., M–F.
4. Enter your new personal code consisting of 4–8 digits,
then press ENTER.
5. Re-enter your new personal code and press ENTER again.
Proceed to fingerprint scan procedure.
To enter fingerprint scans
Tips for fingerprint
programming and usage
Best finger for programming
• Do not choose a finger with a cut or scar.
• Do not choose a finger with excessively long fingernails.
• Choose a finger with the tightest swirl pattern.
Finger placement
• Place your finger on the sensor in a direct manner. Do not slide
or roll your finger onto the sensor.
• Do not move your finger off of the sensor until the lights
around the sensor turn off.
• Any trembling or shaky movement of the finger will result in an
inaccurate reading.
• Use a medium pressure on the sensor. Too firm or too light
will not read correctly.
Location of finger on the sensor
• Look to see where the swirl part of your fingerprint is on
your finger.
• Place the swirl part of your fingerprint on the sensor.
• With your finger on the sensor, note the position of your
fingernail in relation to the sensor crosshairs. Repeatable
placement of the finger is important in programming and usage
of the safe.
• Also note where you are standing in relation to the safe.
Programming or usage at a different angle will not work well.
Skin condition
• If you have dirt on your hands, please wash them before using
the safe.
• Very dry skin will not program well. Use a skin moisturizer,
being sure to rub the moisturizer in well and remove any
excess before using the safe.
NOTE: Should you choose not to enter your fingerprint
scan at the first use, it can be entered at a later
date. The original Factory Code is necessary to
continue at that later date.
NOTE: The fingerprint lock stores one manager and up
to six (6) users. The manager and each user is
encouraged to program two fingers, preferably
one finger from each hand.
1. To store your first fingerprint, place one finger on the sensor
and follow prompts as they appear on the LCD screen.
(Fig. K) Three accurate reads of the fingerprint are necessary
for successful enrollment. Remember how you place your
finger on the sensor and try to position it in the same place
each time.
2. After successful enrollment of the first finger, to store the
second fingerprint, press the number 2 and repeat Step 1
using a different finger, preferably one from the other hand.
You may enroll additional users at this time or at a later date.
K
Normal use
To access the safe, first turn the key to the right to unlock. You
may then either press the ENTER button and place your finger
on the sensor (Fig. K), or, enter your personal code and press
ENTER. LCD will prompt the next steps.
For optimal accuracy and fingerprint-reading success, clean the
fingerprint sensor periodically with a lint-free cloth.
Enrolling and deleting users
To enroll a new user or delete an existing user, enter your
personal code or manager fingerprint scan and press ENTER.
Enter a user number (1-6) and follow the prompts which
appear on the screen.
Backup
The system memory can be returned to its original status using
this sequence and following the screen prompts:
99 > CLEAR > 2004 > ENTER
CAUTION: This action PERMANENTLY ERASES all
memory, personal codes and fingerprint
scans.
CAUTION: ENVIRONMENTAL CONDITIONS
The electronics may not work or may have
a slow reaction time in cold temperatures
(50°F or less). Make sure the safe is at room
temperature before programming and usage.
5
Publicidad
