Publicidad
Idiomas disponibles
Idiomas disponibles
USE
Technical data :
Place load EN50242
Capacity with pans & dishes 4 persons
Water supply pressure (litres) 3
Power
Wash pump power
A Programme selection indicator lights
B Programme selection button
C Programme description
D On/off button
The dishwasher and the oven cannot be used simultaneously.
Setting a programme
Open the door and press the On/off button ; the 4 Program selection LEDs start flashing.
- Set the required programme by pressing Programme selection button, LED of the chosen programme will turn on (2 LEDs for COLD
RINSE programme).
- Close the door (after audible signal), the chosen programme will start automatically.
USE THE DISHWASHER
Opening the door
Grip the handle in the front panel and pull forward. If the machine
comes open while it is working, an electrical safety device
automatically switches everything off. For the machine to work
properly, the door should not be opened while it is in operation.
Closing the door
Place the basket in the dishwasher. Make sure that the spray arm
is free to rotate and is not obstructed by cutlery, crockery or pans.
Close the door, pressing on it to make sure it is firmly shut.
Interrupting a programme
lt is not recommended that the door be opened while a programme
is running, and especially not during the main wash phase and
final drying.
However, the appliance stops automatically when the door is
opened.
When the door is closed again, the programme continues
automatically.
If you wish to change or cancel a programme that is running, carry
out the following procedure:
. open the door, keeping the Programme selection button "P"
pressed in until all 4 indicator lights are flashing. The current
programme is cancelled. A new setting can now be made.
Before starting a new programme, you should check that there is
still detergent in the dispenser. If necessary, top up the dispenser.
WARNING: if the door is opened during the drying phase, an
intermittent audible signal is activated to advise that the cycle is
not yet completed.
End of programme
The end of the programme is indicated by an audible signal. When
the door is opened the programme selection indicator lights start
flashing. Release the On/off button.
Deactivating the audible signal
The audible function can be deactivated in the following way:
- press the On / Off button,
- wait till the programme LEDs blink,
- within 2 minutes, press and keep pressed for at least 30 seconds
the Programme Selection button (the programme LEDs will still
blink and an intermittent audible signal is heard).
- Once the first two LEDs on the left are illuminated without blinking
and the audible signal is off, release the button (the audible
signal function is active).
- Press again the Programme Selection button, the first two LEDs
on the left will go off and the other two LEDs will turn on (the
audible signal function is deactivated).
- An audible signal will confirm that the setting is completed
- To set again the audible signal function repeat the whole
procedure.
Attention - The dishwasher is equipped with an anti-overflow
safety device which in the event of anomaly intervenes by
evacuating water in excess.
THE DISHWASHER
6
Drainage pump power
Max power absorbed
Water pressure
1900 W
150 W
Fuse (amp)
DISHWASHER CONTROLS
SELECTING THE PROGRAMMES AND SPECIAL FUNCTIONS
30 W
2050 W
mini 0,08 - max 0,8 MPa
10 A
Fault Signals
If malfunctions or faults occur when a program is running, the
LED that corresponds to the selected cycle (2 LEDS for COLD
RINSE programme) will blink rapidly and an audible signal will be
activated.
In this case, turn the dishwasher off by pressing the On / Off
button. After checking to make sure the water inlet hose tap is
open, that the drain hose is not bent and that the siphon or filters
are not clogged, re-start the selected program. If the anomaly
persists, contact Customer Service.
Important !
To ensure the correct operation of the anti-overflow safety
device, it is recommended not to move or to tilt the dishwasher
during operation.
If it is necessary to move or to tilt the dishwaher, first make
sure the washing cycle is finished and that no water is left
in the tank.
PRELIMINARY OPERATIONS AND CLEANING
THE FILTER UNIT
flat filter, which traps the smallest food particles ensuring a perfect
rinse.
For best results, the filter unit should be checked and cleaned
after each wash.
To remove the filter unit, simply grip the handle and lift the whole
unit out.
The central cup is just resting on top for easy cleaning.
The dishwasher is fitted with a self cleaning micro filter, which
only requires checking about once every 15 days.
However, it is advisable to check after every wash, that the central
cup and the flat filter are not clogged.
NB : After cleaning the filters, make sure that they are correctly
reassembled, one inside the other, and that the flat filter is properly
positioned at the bottom of the dishwasher.
A poor seating of the filter unit could have an adverse effect on
the efficiency of the appliance.
Important : Never use the dishwasher without filter.
5 GB
The filtering system is composed
of :
- a central filter cup which traps the
largest food particles.
- a flat filter which continuously filters
the washing water.
- the micro filter, situated under the
Publicidad
