Cleaning, Maintenance And Ordering Spare Parts - EINHELL CE-CP 18/180 Li E Manual De Instrucciones

Finish-polishing
•
Use the synthetic polishing attachment (Fig.
11) to remove the layer of polishing agent and
finish the polishing work.
•
To fit the synthetic polishing attachment,
pull the edge upwards (Fig. 10), press the
attachment onto the hook-and-loop surface
of the polishing disk and then pull the edge
downwards again (Fig. 11). The edge of the
polishing disk is covered by the polishing
attachment.
•
Important! Do not exert any pressure on the
polishing machine!
Care tips
•
Wash your automobile at least every 2 weeks.
Avoid the use of household washing agents
as they might damage the paintwork and
remove the wax layer.
•
Wash your automobile with a clean sponge.
Work from top to bottom.
•
Insects, bird droppings and tar marks should
be removed from the surface of the paintwork
on a daily basis.
•
To prevent glass cleaner getting on the
paintwork, spray it on a cloth rather than
directly onto the window.
6.4 Using as a sanding machine
Use the supplied sanding attachments (Fig. 12)
for sanding purposes.
The hook-and-loop fastener enables easy
changing of the sanding attachments.
•
Place the whole surface area of the sanding
disk on the material.
•
Move the machine with gentle pressure over
the "workpiece", making circular or transverse
and linear movements.
•
Use a coarse grit for coarse sanding and
a finer grit for finish sanding. You can find
the best grit size for the job by carrying out
sanding tests.
6.5 Speed control indicator (Fig. 3)
Use the speed control to set the desired working
speed.
Press the "+" button to increase the speed.
Press the "-" button to decrease the speed.
Refer to the display (7) for the set speed. Set
speed = Display x 100
Important! Set the equipment's operating speed
and allow it to reach the set speed before you
place it on the surface you want to machine. This
can take a few seconds depending on the speed.
Anl_CE_CP_18_180_Li_E_SPK7_USA.indb 16 Anl_CE_CP_18_180_Li_E_SPK7_USA.indb 16
EN
7. Cleaning, maintenance and
ordering spare parts
HAZARD!
Always take the battery out of the equipment
before starting any cleaning work.
7.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it down with compressed air at
low pressure.
•
We recommend cleaning the equipment
immediately each time after use.
•
Clean the equipment regularly with a damp
cloth and some soft soap. Do not use
cleaning agents or solvents; these may
be aggressive to the plastic parts in the
equipment. Ensure that no water can get into
the interior of the equipment. The ingress of
water into an electric power tool increases the
risk of an electric shock.
•
Wash the polishing bonnets only by hand and
let them air-dry.
•
When the polishing machine is not being
used it should be stored face up with the
polishing bonnet removed so that the
polishing disk can dry and retain its original
shape.
7.2 Maintenance
There are no other parts inside the equipment
which require maintenance.
7.3 Ordering replacement parts:
Service
1. If your power tool requires service,
contact an authorized Einhell USA dealer
or call the Einhell USA customer service
center at 1-866-EINHELL
(1-866-346-4355). Only identical
replacement parts should be utilized for
repairs. This will ensure that the safety of the
power tool is maintained.
2. If the battery charger cable is damaged, it
must be immediately replaced to avoid a
hazard. Contact the Einhell USA
service center at 1-866-EINHELL
(1-866-346-4355) for assistance.
- 16 -
customer
®
11.11.2019 07:52:19 11.11.2019 07:52:19