Safety Instructions - EINHELL DELS 180 Manual De Instrucciones

Anleitung DELS 180
GB
Please read the operating instructions carefully and
observe the safety regulations at all costs. Keep the
operating instructions together with the triangular
sander.

SAFETY INSTRUCTIONS

Warning! When using electric tools, basic safety
precautions should always be followed to reduce the
risk of fire, electric shock and personal injury, in-
cluding the following.
Read all these instructions before attempting to operate
this product and safe these instructions.
For safe operation:
1. Keep work area clean
– Cluttered areas and benches invite injuries.
2. Consider work area environment
– Don't expose power tools to rain. Don't use power
tools in damp or wet locations. Keep work area well lit.
Don't use power tools in presence of flammable liquids
or gases.
3. Guard against electric shock
– Prevent body contact with grounded surfaces (e.g.
pipes, radiators, ranges refrigeratiors).
4. Keep children away
– Do not let visitors contact tool or extension cord. All
visitors should be kept away from work area.
5. Store idle tools
– When not is use, tools should be stored in dry, high, or
locked-up place, out of the reach of children.
6. Don't force tool
– It will do the job better and safer at the rate for which it
was intended.
7. Use right tool
– Don't force small tools or attachments to do the job of
heavy duty tool. Don't use tools for purposes not
intended: for example, don't use circular saw for cutt- ing
tree limbs or logs.
8. Dress properly
– Do not wear loose clothing or jewelry. They can be
caught in moving parts. Rubber gloves and nonskid
footwear are recommended when working outdoors.
Wear protective nair covering to contain long hair.
9. Use safety glasses
– Also use face or dust mask if cutting operation is
dusty.
10. Don't abuse cord
– Never carry tool by cord or yank it to disconnect it from
receptacle. Keep cord from heat, oil and sharp edges.
11. Secure work
– Use clamps or a vise to hold work. It's safer than using
your hand and it frees both hands to operate tool.
12. Don't overreach
– Keep proper footing and balance at all times.
4
02.11.2001 10:59 Uhr Seite 4
13. Maintain tools with care
– Keep tools sharp and clean for better and safer
performance. Follow instructions for lubricating and
changing accessories. Inspect tool cords periodically
and, if damaged, have repaired by authorized service
facility. Inspect extension cords periodically and replace
if damaged. Keep handles dry, clean and free from oil
and grease.
14. Disconnect tools
– When not in use, before servicing, and when
changing accessories such as blades, bits and cutters.
15. Remove adjusting keys and wrenches
– Form the habit of checking to see that keys and
adjusting wrenches are removed from tool before turning
it on.
16. Avoid unintentional starting
– Don't carry plugged-in tool with finger on switch. Be
sure switch is off when plugging in.
17. Outdoor use extension cords
– When tool is used outdoors, use only extension cords
intended for use outdoors and so marked.
18. Stay alert
– Watch what you are doing. Use common sense. Do
not operate tool when you are tired.
19. Check damaged parts
– Before further use of the tool, a guard or other part
that is damaged should be carefully checked to
determine that it will operate properly and perform its
intended function. Check for alignment of moving parts,
binding of moving parts, breakage of parts, mounting,
and any other conditions that may affect its operation. A
guard or other part that is damaged should be properly
repaired or replaced by an authorized service center
unless otherwise indicated elsewhere in this instructions
manual. Have defective switches replaced by an
authorized service center. Do not use tool if switch does
not turn it on and off.
20. Warning
– The use of any other accessory or attachment other
than recommended it this operating instruction or the
Einhell catalog may present a risk of personal injury.
21. Have your tool repared by an expert
– This electric appliance is in accordance with the
relevant safety rules repairing of electric appliances may
be carried out only by experts otherwise it may cause
considerable danger for the user.
22. Connect the dust extraction device
Wherever there are facilities for fitting a dust
extraction system, make sure it is connected and used.
23. Always remove the plug from the socket before doing
any work on the machine (cleaning, changing sanding
paper etc.).
24. Never remove the plug from the socket by pulling on the
power cable.