Speci¿ C Safety Rules; Pre-Start Checks - Altrad Belle MEGAVIB+ Manual Del Operador

GB
Personal Safety
· STAY ALERT, watch what you are doing and use common sense when operating a power tool.
· DO NOT USE TOOL while tired or under the inÀ uence of drugs, alcohol, or medication. A moment of inattention while operating
power tools may result in serious personal injury.
· DRESS PROPERLY.
· AVOID accidental starting.
· BE SURE switch is off before plugging in. Carrying tools with your ¿ nger on the switch or plugging in tools that have the switch on
invites accidents.
· REMOVE adjusting keys or spanners before turning the tool on. A spanner or a key that is left attached to a rotating part of the tool
may result in personal injury.
· DO NOT overreach.
· KEEP proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected
situations.
· USE safety equipment.
Tool Use And Care
· DO NOT FORCE the tool.
· USE the correct tool for your application. The correct tool will do the job better and safer at the rate for which it is designed.
· DO NOT USE tool if switch does not turn it on or off. Any tool that cannot be controlled with the switch is dangerous and must be
repaired.
· DISCONNECT the plug from the power source before making any adjustments, changing accessories, or storing the tool. Such
preventive safety measures reduce the risk of starting the tool accidentally.
· STORE idle tools out of reach of children and other untrained persons. Tools are dangerous in the hands of untrained users.
· CHECK for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tools
operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools.
· USE only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool,
may become hazardous when used on another tool.
GB
· For the safe and proper operation of the 'MEGAVIB+', make sure that operators have been instructed in the correct use of this
machine.
· Before connecting the motor to the electrical system, make sure that the voltage and frequency match with the ones stated on
the machine serial plate, located in the top part of the plastic housing.
· ENSURE that all housing screws are tight before starting work.
· AVOID the À attening of the cable by heavy machinery with could cause breakage.
· DO NOT CONNECT the À exible shaft to the power unit when it is working.
· DO NOT OPERATE the motor when this is working and without transmission.
· DO NOT WORK with transmission or poker in bad conditions, the motor overheats.
· DO NOT WORK with the plastic housing broken.
· DO NOT PERMIT untrained personnel to operate the motor or connections.
· MAINTAIN free ventilation of air.
· KEEP the motor in a clean and dry area.
· MAKE SURE that the electrical cable is with the proper section and functioning properly.
· BEFORE DOING any type of repair, DISCONNECT the motor from the electrical system.
· WHEN CONNECTING to a generator, make sure that the output voltage and frequency is stable, right, and has the proper power,
(the converter's feeding voltage should not vary more than ± 5% as stated on the motor's plate).
· WHEN FINISHING the job or when taking a break, the operator should unplug, disconnect it from the electrical system, and have it
placed in such a way that it should not fall or tip.
· In addition, all local regulations should be respected.
Vibration
Some vibration from the poker is transmitted through the À exible hose to the operator's hands.
PPE (Personal Protective Equipment).
Suitable PPE must be worn when using this equipment i.e. Safety Goggles, Gloves, Ear Defenders, Dust Mask and Steel Toe capped
footwear. Wear clothing suitable for the work you are doing. Always protect skin from contact with concrete. Suitable ear defenders
Should be used because the acoustic power level of this machine is 92 dB and the acoustic pressure level is 86 dB.
GB
1. Before starting the job, ensure all handling and safety devices are operating correcting.
2. Regularly inspect the condition of the electrical cables
3. If defects are found in the safety devices or other defects which could reduce the safe handling of the equipment, notify the
proper responsible person immediately.
General Safety
Speci¿ c Safety Rules

Pre-Start Checks

8