Battery Recharging - MELICONI HP STETO Instrucciones De Uso

2.4ghz

Tabla de contenido

Idiomas disponibles

- Use the "5" audio cable with the 2 stereo connectors, to connect the audio input «Z» (AUDIO IN) of the base to the audio source

output (TV).

- Switch on the base and the audio device connected.

- After ﬂ ashing for a few moments the green LED «P» of the base remains switched on.

- Usually the device connected (TV) will no longer reproduce audio through its own speakers

- Use the TV remote control to set the audio volume to at least 50%.

Wait for a minute and check that the green LED "P" on the base remains on, indicating that there is a sufﬁ cient audio signal in input.

IMPORTANT: on some models of TV it is necessary to activate the headphones audio output and increase its volume, via the

MENU, so that it is suitable for use as the input audio signal for the base. When the input audio signal to the base is present, and

sufﬁ ciently strong, the green LED «P» on the base remains on.

- Remaining near the base, switch on the headphones by positioning the switch «A» to ON. Check that the green LED signal

indicator «B» is switched on.

- Put on the headphones and adjust the volume with the volume wheel «C» until you achieve the desired audio, if necessary adjust

the balance control "F" on the rear of the headphones.

If no sound comes from the headphones, or if the audio is distorted see the "TROUBLESHOOTING" chapter.

For normal use simply switch the headphones on and off with the ON/OFF switch «A» on the headphones, moving it

from OFF to ON.

The base transmitter will switch off automatically after 5 minutes in the absence of an input audio signal, or when the

headphones are placed on the base; when the input audio signal returns the transmitter switches on automatically.

When the headphones are not used, after switching them off, place them on the base charging support "M" and check

that the LED «Q» switches on. This will ensure that they will be charged for the next use.

If the headphones are not used for long periods disconnect the AC power supply unit from the mains.

The HP Steto headphones are ﬁ tted with an internal microphone, simply press button «D» (MIC) to interrupt the audio

signal from the connected device and listen to ampliﬁ ed voices and sounds from the surrounding environment; the

indicator lamp «B» turns red. Press the MIC button again to resume listening from the device connected; the indicator

lamp «B» turns green.

IMPORTANT:

- During normal use the green LED «P» on the base must remain always on. When it is off or ﬂ ashing it means that the

input audio signal to the transmitter is low or missing. Therefore turn up the volume on the TV until the LED switches

on and remains on.

To adjust the listening volume use the volume wheel «C» on the headphones and NOT the volume on the source device

(TV). If no sound comes from the headphones, or if the audio is distorted see the "TROUBLESHOOTING" chapter.

To recharge the batteries position the headphones ON/OFF switch to OFF and place them on the base. Make sure that

the LED «Q» switches on.

The LED «Q» remains red until the battery is fully charged, whereupon it turns green; the battery may take up to three

hours to recharge

A spare battery is included for extended use. Simply insert it in the transmitter base slot «S» to charge it. When the spare

battery is being charged the LED indicator «R» is red.

It turns green when the battery is completely charged.

The headphones will work for at least 4 hours on a fully charged battery.

Leaving the headphones charging on the base, even for several days, will not cause any problems.

WARNINGS:

When the headphones are not being used switch them off to avoid draining the batteries completely and damaging

them.

Always ensure that the slider switch «A» is in the OFF position when recharging the batteries.

IMPORTANT:

Dispose of the product in compliance with the applicable standards.

If the audio device that you wish to use does not have a headphone output or you want the TV to continue reproducing

audio from its speakers, use the RCA audio sockets on the TV (red and white "OUTPUT" socket). Connect the audio

cable of the base to the RCA audio outputs of the device, with the adaptor cable "6" (2xRCA male / 3.5 mm. stereo

female) included.

Alternatively you can connect the external microphone supplied "7" to the audio cable and position the microphone

close to the audio source.

Libretto Istruzioni HP STETO 14x20 24_11_2017.indd 15

Use