Mitsubishi Electric PRH-P200MYA Para El Instalador página 11

[4] -3. Mode selection setting
(1) Remote controller main/sub setting
• To switch the setting, press the [
1 Main: The controller will be the main controller.
2 Sub: The controller will be the sub controller.
(2) Use of clock setting
• To switch the setting, press the [
1 ON: The clock function can be used.
2 OFF: The clock function cannot be used.
(3) Timer function setting
• To switch the setting, press the [
followings.).
1 WEEKLY TIMER (Initial setting value):
The weekly timer can be used.
2 AUTO OFF TIMER: The auto off timer can be used.
3 SIMPLE TIMER:
The simple timer can be used.
4 TIMER MODE OFF: The timer mode cannot be used.
* When the use of clock setting is OFF, the "WEEKLY TIMER" cannot be used.
(4) Contact number setting for error situation
• To switch the setting, press the [
1 CALL OFF: The set contact numbers are not displayed in case of error.
2 CALL **** *** ****: The set contact numbers are displayed in case of error.
CALL_: The contact number can be set when the display is as shown
on the left.
(2) Unit Function Selection
Set the functions of each unit from the remote controller, as required. The functions of each unit can be selected only from the remote controller.
Set the functions by selecting the necessary items from Table 1 and Table 2. (Default settings are also shown below)
Table 1. Itemized functions of the entire refrigerant system (select unit number 00 to 15)
Function
Power failure Not available
automatic recovery Available
Indoor temperature Unit operating average
detection Set by unit's remote controller
Remote controller's internal sensor
LOSSNAY Not Supported
connectivity Supported (unit is not equipped with outdoor-air intake)
Supported (unit is equipped with outdoor-air intake)
Power voltage 240 V
220 V, 230 V
Table 2. Itemized functions of the unit (select unit numbers 01 to 04 or AL)
Function
100 Hr
Filter sign
2500 Hr
No filter sign indicator
Operation
Fan operation
during thermo off
Stop
in heating
operation
Fan operation Operation
during thermo off
in cooling Stop
operation
Note:
When the indoor unit functions were changed using the function selection after installation is complete, always indicate the set contents by entering
mark in the appropriate check field of Table 1 and Table 2.
ON/OFF] button.
ON/OFF] button.
ON/OFF] button (Choose one of the
ON/OFF] button.
Settings
Settings
• Setting the contact numbers
To set the contact numbers, follow the following procedures.
Move the flashing cursor to set numbers. Press the [
button to move the cursor to the right (left). Press the [
button to set the numbers.
[4] -4. Display change setting
(1) Temperature display °C/°F setting
• To switch the setting, press the [
1 °C: The temperature unit °C is used.
2 °F: The temperature unit °F is used.
(2) Suction air temperature display setting
• To switch the setting, press the [
1 ON: The suction air temperature is displayed.
2 OFF: The suction air temperature is not displayed.
(3) Automatic cooling/heating display setting
• To switch the setting, press the [
1 ON: One of "Automatic cooling" and "Automatic heating" is displayed under the
automatic mode is running.
2 OFF: Only "Automatic" is displayed under the automatic mode.
Mode no. Setting no. Check
1
01
2
1
02 2
3
1
03 2
3
1
04
2
Mode no. Setting no. Check
1
07 2
3
3
25
2
1
27
2
TEMP. (
CLOCK (
ON/OFF] button.
ON/OFF] button.
ON/OFF] button.
Default settings
Remarks
Approx. 4-minute wait-period
after power is restored.
Default settings Remarks
When selecting fan operation
"Stop", set setting no. of Mode
no. "02" in Table 1 to "3". Be sure
to place the remote controller
inside the room to be air-condi-
tioned so that it can monitor the
room temperature.
) and ( )]
) and ( )]
or other
11