Assembly & Operation - Worx WG163 Manual Del Operador

ASSEMBLY & OPERATION
Action
ASSEMBLY
Assembling the Safety Guard
Mounting the Edger Wheel
Installing and Removing the
Battery Pack
Charging the battery pack
More details can be found in
charger's manual
Operation
Safety ON/OFF Switch
Trimming
- Adjusting the Shaft
- Adjusting the Trimmer Head
- Adjusting the Auxiliary handle
- Trimming
- Using the Flower Guard
Edging
- Changing the tool into the Edg-
ing mode
- Edging
Command feeding the line
Manually feeding the line
Replacing the trimmer Spool
Manually winding the line
OPERATION INSTRUCTIONS
WARNING! The charger and battery pack
are specially designed to work together so
do not attempt to use any other devices. Never insert
or allow metallic objects into your charger or battery
pack connections because of an electrical failure and
hazard will occur.
1. Automatic line feed system
When initially switching on the trimmer, a small
2 in 1: Trimmer / Edger
length of line is fed out. Each time the tool is started
from rest it will advance about 0.25 inches of trimmer
line.
Figure
A 'clattering' noise will be heard when the lines hit
the Line Cutter. DO NOT BE ALARMED. This is quite
normal. After about 5 seconds the line will be cut to
the correct length and the noise will reduce as the
See Fig. A1 & A2
motor gains full speed.
If the noise of the line being cut can't be heard, more
See Fig. B
line will need to be fed out.
To feed more line, it is first necessary to allow the
trimmer to stop completely; it must come to a
See Fig. C
complete rest, then restart, allowing the motor to
reach full speed.
Repeat above until you hear the line hitting against
See Fig. D
the Line Cutter.
2.
Your trimmer is equipped with a Command Feed
See Fig. E
System. For efficiently feeding the line, just press the
command feed button while the machine is running
until you hear the 'clattering' noise of the line cutting.
The motor will shut off when pressing the Command
See Fig. F
Feed button and will restart when releasing
the button. During that process the line will
See Fig. G1, G2
automatically feed additional line for cutting.
See Fig. H
3. Manually feeding the line (See Fig. M)
Turn off the trimmer and remove the battery. If
See Fig. I1
required, line can be fed out manually. To operate,
See Fig. I2
press and release manual Line Feed Button, while
gently pulling out the line until it is long enough to
reach the Line Cutter. If the line extends past the Line
Cutter, too much line has been fed out. If too much
line is fed out, remove the Spool Cap and turn Spool
See Fig. J1, J2
counter-clockwise until the line is at the desired
length.
See Fig. K
4. Manually winding the line ( See Fig. O1, O2,
See Fig. L
O3, O4)
Take approximately 10ft (3m) of line. Insert 5/8 inch
See Fig. M
(15mm) of line into the Spool holes and wind line in
the direction of the arrows on the top of the Spool.
See Fig. N1, N2,
Leave approximately 4 inches (100mm) of line
N3
unwound and place into the cleat. Ensure that the
line is neatly coiled on the Spool. Failure to do so will
See Fig. O1, O2,
impair the efficiency of the automatic line feed. Then
O3, O4
fit the Spool as shown in Fig. N1, N2, N3
MAINTENANCE
After use, disconnect the battery from the tool and
check for damage.
Your power tool requires no additional lubrication
or maintenance. There are no user serviceable parts
in your power tool. Never use water or chemical
cleaners to clean your power tool. Wipe clean with a
dry cloth. Always store your power tool in a dry room
temperature location. Keep the motor ventilation
slots clean. Keep all working controls free of dust.
TM
(See Fig. L)
11
EN