Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
ION
,su trac-
)a el mejor
on de este
,continuacion:
nstrucciones
a caja de
_rgada en
forma c6rnoda
_das en forma
o, las !lantas
brica.)
ador est_
e lado a lado
para olotener
3rte. (Las
_sen forma
Jny de ta
_rran el paso
leas y dentro
_rreas.
ue todas las
uras y que los
"haadecuada.
_egL_reseque
,n la posici6n
(Vea "PARA
n de la Oper-
como usar su
s puntos de
;ontinuacion:
egar at nivel
.me que estar
_gular, nueva y
ntroles - su
:os antes de
_renos est6 en
:gura.
de Presencia
Funcionamien-
lodo adecuado
tamiento y
mston antes
hera vez. Siga
ara el empiezo
PESAR EL
A TRANSMIS-
_ci6n de este
.
2.
.
4.
.
6_
Positive
(Red)
Cable
Lift hood to raised
position.
Disconnect
BLACK
battery
cable (A)
then RED battery
cable and carefully
remove battery
from tractor.
Install new battery
with terminals
in
same position
as old battery.
First connect
RED battery cable (B) to
positive
(+) battery terminal
with hex
bolt and keps nut as shown. Tighten
securely.
Slide terminal
cover (C) over
terminal.
Connect
BLACK
grounding
cable to
negative
(-) battery terminal
with re-
maining
hex bolt and keps nut. Tighten
securely
f
--,..
Negative
Close hood.
(_
(Black)
Cable
TO REPLACE
HEADLIGHT
BULB
1. Raise hoed.
2.
Remove
bulb holder from the hole in
the backside
of the grill.
3.
Replace
bulb in holder and install bulb
holder securely
back into the hole in
the backside
of the grill.
4.
Close hood,
INTERLOCKS
AND RELAYS
Loose or damaged
wiring
may cause
your tractor
to run poorly, stop running,
or
prevent it from starting.
• Check wiring.
See electrical
wiring
diagram
in the Repair
Parts section.
TO REPLACE
FUSE
Replace with 30 amp automotive-type
plug-in fuse.
The fuse holder is located
behind the dash.
TO REMOVE
HOOD AND GRILL
AS-
SEMBLY
1. Raise hood.
2.
Unsnap
headlight
wire connector.
3.
Stand in front of tractor.
Grasp hood at
sides, tilt toward
engine and lift off of
tractor.
4.
When replacing
hood, be sure to re-
connect
the headlight
wire connector.
Hood
Headlight Wire
Connector
ENGINE
Maintenance,
repair, or replacement
of
the emission
control devices
and systems,
which are being done at the customers
ex-
pense, may be performed
by any non-road
engine repair establishment
or individual.
Warranty
repairs
must be performed
by an
authorized
engine manufacturer's
service
outlet.
TO ADJUST
THROTTLE
CONTROL
CABLE
The throttle
control
has been preset at the
factory and adjustment
should
not be nec-
essary.
Check
adjustment
as described
below before
loosening
cable.
If adjust-
ment is necessary,
proceed
as follows:
I.
With engine not running,
move throttle
control
lever
to fast position.
2. Check
that swivel is against stop.
If it is
not, loosen cable clamp screw and pull
cable back until swivel is against
stop,
Tighten
cable clamp screw securely.
29
Publicidad
Tabla de contenido
