The Flex Valve - Tippmann X7 Phenom Manual Del Usuario

The Flex Valve

It is not necessary to disassemble the Upper Receiver to access and service the Flex Valve
assembly or its internal parts. The Valve can be slid out the back of the receiver as described
on pages 18 -19.
Disassembly instructions:
1. Inspect and clean the exterior of the Valve assembly (item 8 on page 18, item 1 here).
2. Remove the
Bumper Disk
Replace if damaged.
3. Using a 3/16 or 1/8 allen wrench, remove the
counterclockwise until it is loose. Set aside.
4. Pull the
Spring
workbench, and the
the Regulator Piston with Tippmann grease every 8-10,000 shots and prior to re-
assembly. There is no need to further disassemble the marker for normal maintenance.
5. Hold the Valve Body with your hand while using an adjustable wrench to turn
(counterclockwise) the
the
Regulator Seat
Compression Spring
6. Using a small plastic push rod, gently push from the opposite end of the Valve Body
to remove the
(11).
Spacer
Re-assembly instructions:
1. Always inspect and clean all parts prior to re-assembly. Replace any damaged part.
Lubricate all O-rings and springs with Tippmann
O-rings and to make assembly easier.
2. After greasing O-rings, reinstall the
the Valve Body.
3. Reinstall the
Compression Spring
4. Install the
Compression Spring
5. Ensure the
Regulator Pin Seal
them down into the Valve Body with the Seal side going in first.
6. Clean and inspect the
not damaged); replace the O-ring if damaged. Insert into the Valve Body and turn
clockwise until hand tight and then tighten with an adjustable wrench.
7. Apply Tippmann grease to the
Reinstall into the Regulator Body.
8. Reinstall the
Compression Spring
(23) by threading clockwise into the Regulator Body. Use a 3/16 or 1/8 allen
Adjuster
wrench to turn the Velocity Adjuster until the O-ring is not visible.
: Further adjustment is done when measuring velocity (see page 12).
Note
9. Reinstall the
Spacer Washer
10. Apply Tippmann grease to the outside surface of the
grease to the inside bore of the Power Tube.
11. Reinstall the
Front Bolt
page 18) to the assembly at this time to make further reassembly easier. Make sure to
apply grease to these parts.
(8) and the
(22) out the back. Lightly tap the rear of the Valve Body on the
Regulator Piston
Regulator Body
(15),
Regulator Pin Seat
(12) easily come out of the Valve Body.
(9),
Firing Spool Compression Spring
(14) is installed onto the
Regulator Body
Regulator Piston
(7) and the
(item 7 on page 18) and
Spacer Washer
Velocity Adjuster
(21) comes out. Inspect, clean, and lubricate
(20) out from the Valve Body. Once removed,
(14),
Regulator Pin
grease to help prevent damage to
®
(9), making sure it bottoms out inside
Firing Spool
(10), and then the
(12) and
Regulator Pin
(20), making sure its O-ring is in place (and
(21) complete outside surface.
(22) into the Regulator Body. Install the
Bumper Disk
Power Tube
Compression Spring
21
(7). Clean and inspect.
(23) by rotating it
(13), and
(10), and the
Valve Spool
Valve Spool Spacer
(13) together.
(15). Drop
Regulator Seat
(8).
(6). Also apply
(item 6 on
E
N
G
L
I
S
H
(11).
Velocity