HIKOKI C 6SS Instrucciones De Manejo página 7

PRECAUTIONS ON USING CIRCULAR SAW
1. Do not use saw blades which are deformed or
cracked.
2. Do not use saw blades made of high speed
steel.
3. Do not use saw blades which do not comply
with the characteristics specified in these
instructions.
4. Do not stop the saw blades by lateral pressure
on the disc.
5. Always keep the saw blades sharp.
6. Ensure that the lower guard moves smoothly
and freely.
7. Never use the circular saw with its lower guard
fi xed in the open position.
8. Ensure that the retraction mechanism of the
guard system operates correctly.
SPECIFICATIONS
Model
Voltage (by areas)*
Cutting Depth
Power Input*
No-Load Speed
Weight (without cord)
* Be sure to check the nameplate on product as it is subject to change by areas.
STANDARD ACCESSORIES (INCLUDE SIDE
HANDLE)
(1) Saw Blade (mounted on tool) ..................................1
( Dia. 165 mm .............................. C6SS
Dia. 190 mm .............................. C7SS
(2) Hex. Bar wrench .........................................................1
(3) Side handle ........................................................ 1 or 0
The items that are included as standard accessories
(including the side handle) vary depending on the region.
Standard accessories are subject to change without
notice.
OPTIONAL ACCESSORIES (sold separately)
(1) Dust Collector Set (D)
Connect the suction hose to collect saw dust with
the vacuum cleaner (see Fig. 9).
(2) Washer (A) ......for 19 mm (Hole dia. of saw blade)
................ for 20 mm (Hole dia. of saw blade)
............. for 25.4 mm (Hole dia. of saw blade)
................ for 30 mm (Hole dia. of saw blade)
NOTE
If the saw blade supplied with your circular saw
has a hole diameter of 15.9 mm, only saw blades
with the same size hole diameter can be fitted to
your circular saw.
(3) Guide (with wing-bolt)
Optional accessories are subject to change without notice.
90° 57 mm
45° 38 mm
3.2 kg
(Aluminum Base)
)
9. Never operate the circular saw with the saw
blade turned upward or to the side.
10. Ensure that the material is free of foreign matters
such as nails.
11. For model C6SS, the saw blades range should
be from 165 mm to 160 mm.
For model C7SS, the saw blades range should
be from 190 mm to 185 mm.
12. Disconnect the plug from the receptacle before
carrying out any adjustment, servicing or
maintenance.
C6SS
(110 V, 120 V, 220 V, 230 V 240 V)
1050 W (110 V: 1010 W)
5500 /min
3.1 kg
(Aluminum Base)
(Steel Base)
APPLICATION
Cutting various types of wood.
PRIOR TO OPERATION
1. Power source
Ensure that the power source to be utilized
conforms to the power requirements specified on
the product nameplate.
2. Power switch
Ensure that the power switch is in the OFF position.
If the plug is connected to a receptacle while the
power switch is in the ON position, the power
tool will start operating immediately, which could
cause a serious accident.
3. Extension cord
When the work area is removed from the power
source, use an extension cord of sufficient thickness
and rated capacity. The extension cord should be
kept as short as practicable.
4. Prepare a wooden workbench (Fig. 1)
Since the saw blade will extend beyond the lower
surface of the lumber, place the lumber on a
workbench when cutting. If a square block is utilized
as a workbench, select level ground to ensure it
is properly stabilized. An unstable workbench will
result in hazardous operation.
CAUTION
To avoid possible accident, always ensure that
the portion of lumber remaining after cutting is
securely anchored or held in position.
English
C7SS
68 mm
46 mm
3.4 kg 3.3 kg
(Steel Base)
7