EINHELL Expert TE-XM 305 U Manual De Instrucciones página 46

Anleitung_TE_XM_305_U_SPK8__ 26.09.12 16:31 Seite 46
GB
6.2 Assembling the saw (Fig. 1-3; 6)
To adjust the turntable (17), loosen the locking
n
grip (14) by approx. 2 turns, which frees the
turntable (17).
Press the latched position lever (13), turn the
n
turntable (17) and scale pointer (15) to the
desired angular setting on the dial (16) and lock
into place with the locking grip (14). The saw has
locking positions at angles of - -45°, -30°, -22.5°, -
15°, 0°, 15°, 22.5°, 30°, 45° and 60°, at which you
can engage the latched position lever.
To release the saw from its position at the bottom,
n
pull the fastening bolt (27) out of the motor
mounting while pressing down lightly on the
machine head (4). Turn the fastening bolt (27)
through 90° before releasing it, so that the saw
remains unlocked.
Swing the machine head (4) up until the release
n
lever (3) latches into place.
The clamping devices (8, 21) can be fitted on the
n
left or right of the fixed saw table (18).
Undo the locking screws for the roll base (30).
n
Guide roll base with limit stop (9) over one of the
n
holding bars for the roll base (10) and install on
the fixed saw table (18), tightening the
appropriate locking screw (30) (Figure 6).
Mount the second holding bar for the roll base
n
(10) on the opposite side of the saw and secure
with the appropriate locking screw (30).
When the locking screw (22) is loosened, you can
n
tilt the machine head (4) to the left by up to 45°.
If the saw is used without the base frame, the foot
n
(32) will prevent the saw from tipping forwards
during operation. In this case, turn out the foot
(32) until it touches the surface on which the saw
is standing.
6.3 Assembling the base frame and bolting the
saw to the base frame (Fig. 4-24)
1. Insert the feet (A) from the bottom into the
intermediate struts (C) as shown in Figure 7.
Ensure that the rubber stoppers on the feet (A)
are aligned so that the support surfaces are level.
2. Screw the feet (A) to the intermediate struts (C)
together with the screws (N), washers (H) and
nuts (G), as shown in Figures 8 - 9.
3. Guide the side parts (B) from the top over the
intermediate struts (C).
4. At each connection point screw the side parts (B)
to the intermediate struts (C) using three screws
(L), washers (K) and nuts (I) (Figures 11-12).
5. Insert the two bottom cross struts (E) into the
appropriate openings on one of the intermediate
struts (C) as far as the stop (Figure 13). Screw
the bottom cross struts (E) to the intermediate
strut (C) using two screws (L), washers (K) and
46
nuts (I) in each case, as shown in Figures 14 - 15.
6. On the same side of the base frame, slide the two
top cross struts (F) as far as the stop into the
appropriate openings on the side part (B) (Figure
16). Insert a corner bracing (D) into each opening
on the side part (B). Note, that each of the corner
bracings (D) only fits on one side of the base
frame; this is the case when the openings on the
side part (B), the top cross struts (F) and the
corner bracings are positioned precisely on top of
each other (Figure 17).
7. Now screw the top cross struts (F), corner
bracings (D), side parts (B) together using two
screws (L), washers (K) and nuts (I) in each case,
as shown in Figures 18 - 19.
8. Insert the two base frame parts in such a way that
the bottom and top cross struts (E, F) are
positioned in the relevant openings on the side
part (B) and the cross strut (C) (Figure 20).
9. Screw the bottom cross struts (E) to the other part
of the base frame (Figure 21/1) as described
under 5.
10. Screw the top cross struts (F) to the other part of
the base frame (Figure 21/2) as described under
6.
11. Pull the four rubber stoppers (32) from the bottom
side of the saw (Figure 22).
12. Place the saw onto the base frame so that the
openings in which the rubber stoppers (32) were
held are in line with the four openings on the top
side of the saw mounts (J). Then insert the four
screws (M) through the feet from the top and
screw the saw onto the base frame (Fig. 23 – 24).
6.4 Precision adjustment of the stop for crosscut
90° (Fig. 1, 25/-27)
Fasten the turntable (17) in 0° position.
n
Undo the locking screw (22) and move the
n
machine head (4) all the way to the right using the
handle (1).
Place the 90° angular stop (a) between the blade
n
(7) and the turntable (17).
Adjust the adjustment screw (38) until the angle
n
between the blade (7) and the turntable (17)
equals 90°.
Finally, check the position of the pointer (20) on
n
the scale (19). If necessary, release the pointer
(20) with a crosstip screwdriver, move to the 0°
position of the scale (19) and retighten the
holding screw.
No stop angle included.
n
6.5 Precision adjustment of the stop for miter cut
45° (Fig. 1, 25, 28-29)
Fasten the turntable (17) in 0° position.
n
Undo the locking screw (22) and move the
n