Operation As Wood/Plastics Saw - EINHELL Expert TE-XM 305 U Manual De Instrucciones

Anleitung_TE_XM_305_U_SPK8__ 26.09.12 16:31 Seite 47
machine head (4) all the way to the left using the
handle (1), until it coincides at 45°.
Place the 45° stop angle (b) between the blade
n
(7) and the turntable (17).
Adjust the adjustment screw (37) so that the
n
angle between the blade (7) and the turntable
(17) equals exactly 45°.
No stop angle included.
n

7. Operation as wood/plastics saw

7.1 Cross cut 90° and turntable 0° (Fig. 1-3, 30)
For cutting widths up to approx. 100 mm it is possible
to fix the saw's drag function with the locking screw
for drag guide (25) in rear position. If the cutting width
exceeds 100 mm you must ensure that the locking
screw for drag guide (25) is slackened and that the
machine head (4) can be moved.
Move the machine head (4) to its upper position.
n
Use the handle (1) to push back the machine
n
head (4) and fix it in this position if required
(dependent on the cutting width).
Place the piece of wood to be cut at the stop rail
n
(11) and on the turntable (17).
Lock the material with the clamping device (8) on
n
the fixed saw table (18) to prevent the material
from moving during the cutting operation.
Push down the release lever (3) to release the
n
machine head (4).
Press the ON/OFF switch (2) to start the motor.
n
With the drag guide (24) fixed in place: Use the
n
handle (1) to move the machine head (4) steadily
and with light pressure downwards until the saw
blade (7) has completely cut through the
workpiece.
With the drag guide (24) not fixed in place: Pull
n
the machine head (4) all the way to the front and
then use the handle (1) to move it downwards
steadily and with light pressure. Now push the
machine head (4) slowly and steadily to the very
back until the saw blade (7) has completely cut
through the workpiece.
When the cutting operation is completed, move
n
the machine head (4) back to its upper (home)
position and release the ON/OFF button (2).
Important. The integral resetting springs will
automatically lift the machine head. Do not simply let
go of the handle (1) after cutting, but allow the
machine head (4) to rise slowly, applying slight
counterpressure as it does so.
7.2 Cross cut 90° and turntable -52°...+60°
(Fig. 1-3, 31)
The crosscut saw can be used to make crosscuts of
0°- 52° to the left and 0° - 60° to the right in relation to
the stop rail.
Release the turntable (17) by slackening the
n
locking grip (14).
Press the latched position lever (13), turn the
n
turntable (17) and scale pointer (15) to the
desired angular setting on the dial (16) and lock
into place with the locking grip (14). The saw has
locking positions at angles of - -45°, -30°, -22.5°, -
15°, 0°, 15°, 22.5°, 30°, 45° and 60°, at which you
can engage latched position lever.
Retighten the locking grip (14) to secure the
n
turntable (17) in place.
Cut as described under section 7.1.
n
7.3 Miter cut 0°- 45° and turntable 0° (Fig. 1-3, 32)
The crosscut saw can be used to make miter cuts of
0° - 45° in relation to the work face.
If necessary, dismantle the clamping device (8) or
n
mount it on the opposite side of the fixed saw
table (18).
Move the machine head (4) to its upper position.
n
Fasten the turntable (17) in 0° position.
n
Undo the locking screw (22) and use the handle
n
(1) to tilt the machine head (4) to the left until the
pointer (20) coincides with the required value on
the scale (19).
Retighten the locking screw (22) and make the
n
cut as described in section 7.1.
7.4 Miter cut 0°- 45° and turntable 0°- 45°
(Fig. 1-3, 33)
The crosscut saw can be used to make miter cuts to
the left of 0°- 45° in relation to the work face and, at
the same time, 0° - 52° to the left or 0° - 60° to the
right in relation to the stop rail (double miter cut).
If required, dismantle the clamping device (8) or
n
mount on the opposite side of the fixed saw table
(18).
Move the machine head (4) to its upper position.
n
Release the turntable (17) by slackening the
n
locking grip (14).
Use the handle (1) to adjust the turntable (17) to
n
the angle required (in this connection see also
section 7.2).
Retighten the locking grip (14) to secure the
n
turntable in place.
Undo the locking screw (22) and use the handle
n
(1) to tilt the machine head (4) to the left until it
coincides with the required angle value (in this
connection see also section 7.3).
Re-tighten the fixing screw (22).
n
Cut as described under section 7.1.
n
7.5 Limiting the cutting depth (Fig. 34)
The cutting depth can be infinitely adjusted using
n
the screw (34). To do so, undo the knurled nut on
the screw (34) and move the stop for the cutting
GB
47